Used Correa Processing

Dryer-Flaker Drum and Belt 600 mm (23.6 in) Stainless Steel 316 - IPP# 704988

• Manufacturer: APV Mitchell

drum flaker/dryer Single drum design Drum and applicator roll cored for steam heating Drum driven by Carter gearbox, Size MF14/100340 2.71 KW @ 960 rpm belt driven by 3 KW, 3/50/415 volt, 700 rpm flameproof motor...

Dryer-Flaker Drum and Belt 610 mm (24 in) Stainless Steel 304 - IPP# 210324

• Manufacturer: Steel Belt Systems

(2) 20” wide water cooled Rolls are driven by a varispeed drive, one roll is 7" diameter, the other is 16" diameter Material drops onto a stainless steel water cooled belt (similar to a Sandvick). With lump break...

Dryer-Flaker Drum and Belt 1,500 mm (59.1 in) Stainless Steel - IPP# 706652

• Manufacturer: Correa

1.5m wide x 24.85m long rotoform cooling conveyor/belt Drawing Number 6530. 5m long hot water section 17.5m cooling water section Cooling water capacity: 185 GPM @ 30 psi, Hot water zone has 16 sprays x 4 runs x ...

Dryer-Flaker Drum and Belt - IPP# 703637

• Manufacturer: Correa

chrome plate drum only For use with Gouda drum flaker

Dryer-Flaker Drum and Belt 1,050 mm (42 in) - IPP# 49609

chrome plated drum only Cast iron construction

Stainless Steel 304 Steel Belt Systems Dryer-Flaker Drum and Belt - IPP# 229478

• Manufacturer: Steel Belt Systems

approx 28.8 square meter 301 (NICRO 12.1)/304 stainless steel enclosed horizontal belt flaker with Pastillator 1.5m wide x 18000mm cooling length 301 (NICRO 12.1) stainless steel belt 19250mm belt length between ...

Dryer-Flaker Drum and Belt 300 mm (11.8 in) - IPP# 704614

• Manufacturer: R.Simon Dryers

face chrome plated single drum flaker/dryer Drum working pressure 5.5 bar, speed 3 to 21 rpm, cored for steam/hot oil heating

Screw Conveyor by Thomas & Muller 14.75 Diameter Cooling Screw Stainless Steel 304 - IPP# 246772

• Manufacturer: Correa

Rated 2000 lbs./Hr. at 40 lbs./Cu.Ft. Two-(2) 5' 9 &3/8 cooling sections.

Dryer-Flaker Drum and Belt 28 mm (1.1 in) - IPP# 70983

• Manufacturer: APV Mitchell

chrome plated single drum flaker Drum pressure 0.42 bar DC thyristor controlled varispeed drive. Roll speed 10-100 rpm. Heating low pressure steam system of 0.1 bar. Doctor manual adjustable knife made of carbon ...

Dryer-Flaker Drum and Belt 300 mm (11.8 in) Stainless Steel 316 - IPP# 706870

• Manufacturer: Maschinenbau Technik

301/321/316 stainless steel pilot scale horizontal belt flaker system with a pastillator size 300 x 4000mm fabrik #02.331 CE #2.02032, 321 stainless steel belt is driven by a 2.2kw motor via a 1.35kw 316 stainles...

Stainless Steel Dryer-Flaker Drum and Belt - IPP# 228256

• Manufacturer: Berndorf belt systems

belt flaker, with Accu-Drop Pastillator and Variable Speed Drive Belt system is 60" wide x 75 feet long. With six (138" x 59" x 5'5") water collectors 190 Gallon rated for 55 degrees F Six water spray systems, 11...

Belt Conveyor 400 mm (15.7 in) - IPP# 706644

• Manufacturer: Easikit

400mm wide, portable inclined, motor via gearbox, built on /off switch, mounted on wheels

5V21210 Cast Iron V-Belt Pulley 10 Groove 21.20 in O.D J Series Bushing

🔥5V21210 Cast Iron V-Belt Pulley 10 Groove 21.20 in O.D J Series Bushing Small chip on the outside edge can be viewed in the picture. Shouldn't affect anything. Contact for freight quote. INV# P-1814

New England Conveyor Table Top NECV-5V

• Manufacturer: Correa

New England Machinery, model NECV-5V, vacuum belt, 1 to 2 lane diverter. Equipped with 36" infeed / discharge height with a range of ± 2", 4½" wide x 107" long vacuum belt, 10" wide x 54" long vacuum belt, both b...

Span Tech Conveyor Table Top 65" DISCH

• Manufacturer: Correa

Span tech, stainless steel, 12" wide x 141" long flexlink inclined conveyor. 31" long horizontal run leads into 110" incline section. Infeed height range: 30½" to 35½". Discharge height range: 60" to 65". Equippe...