Used Extruders

Trusted Seller
THORESON MCCOSH TD-24
- Manufacturer: Thoreson McCosh
Used Thoreson McCosh Model TD-24 dehumidifying hopper dryer. Serial #206-152-10. Caster mounted dryer includes 50 lb. capacity insulated hopper mounted on stand. 24 CFM. 480 volt, 3 phase, 60 cycle operation at 9...
Hainesport, NJ
Trusted Seller
NOVATEC CDM-750
- Manufacturer: Novatec
- Model: CDM-750
Used Novatec Desiccant Dryer. Model CDM-750, serial number #12-095, new 1994. Has touch screen micro processor control model MCD-1002. Includes (2) approximatey 1000 lb hoppers with receivers and process heaters....
Hainesport, NJ
Trusted Seller
CONAIR 18010902
- Manufacturer: Conair
Used Conair hot air Dryer. Model 18010902, serial #137284. No hopper included.
Hainesport, NJ
Trusted Seller
JOHNSON
- Manufacturer: Johnson
Used Johnson roll pull roll stand Has (2) 54" x 8" diameter rubber covered rolls Rolls are driven by 10 hp DC motor Drive-All 4-speed gearbox Air actuated top pull roll
Hainesport, NJ
Trusted Seller
2003 WERNER & PFLEIDERER ZSK20
- Manufacturer: WP
- Model: ZSK20
Used 20mm Werner & Pfleiderer model ZSK20 co-rotating twin screw extruder. Has 40/1 L/D barrel at 43" centerline height driven through a 3:1 gearbox with a 37-Newton meter torque capacity per screw shaft. Extrude...
Hainesport, NJ
Prism TSE 16TC Benchtop Twin Screw Extruder 65113
- Manufacturer: Bidservice
The PRISM TSE 16 TC extruders are designed for bench-top operation. The horizontally split barrels are quick to open, giving easy access to screws and process contact surfaces for cleaning or configuration change...
$12,500 USD
Freehold Township, NJ
Trusted Seller
Auction
LUFKIN EXTRUDER, SIZE D390B, RATIO 17.55:1, INPUT RPM 1750, 400 HP, SN 115, 6 ZONES PLUS EXTRUDER NO
- Manufacturer: Lufkin
LUFKIN EXTRUDER, SIZE D390B, RATIO 17.55:1, INPUT RPM 1750, 400 HP, SN 115, 6 ZONES PLUS EXTRUDER NOSE, SCREEN CHANGE ADAPTOR, HYDRAULIC UNIT, FEED HOPPER, CONTROL PANEL, NOTE: NOT COMMISSIONED [EAST BLDNG]
Kingsville, Canada
Visit Auction Website
6″ Davis Standard 34:1 -500 HP -Vented (2 vents) Extruders (2 available)
- Manufacturer: Davis-Standard
6″ Davis Standard 34:1 -500 HP -Vented (2 vents) Extruders (2 available)
Rockville Centre, NY
2.5″ Davis Std. 24:1 Air Cooled Extruder – New 1998
- Manufacturer: Davis-Standard
2.5″ Davis Std. 24:1 Air Cooled Extruder – New 1998′ 24:1 – Air Cooled – Non-Vented
Rockville Centre, NY
3.5″ Davis Standard 24:1-Air Cooled -N-Vented Extruders (3) 1998
- Manufacturer: Davis-Standard
3.5″ Davis Standard Extruders Model #MV35IN35 – New 1998 (Three Available) Air Cooled 24:1 L/D Non-Vented HP 158 Gear Ratio: 17.39 SF 1.25
Rockville Centre, NY
2.5″ Davis Standard 24:1 Air Cooled Extruder – New 1998
- Manufacturer: Davis-Standard
2.5″ Davis Standard 24:1 Air Cooled Extruder – New 1998 24:1 – Air Cooled – Non-Vented
Rockville Centre, NY
Trusted Seller
2008 COPERION ZSK-40-MEGA
- Manufacturer: Coperion Waeschle
Used 40mm Coperion Mega 40 co-rotating twin screw extruder. New 2008. No barrels or screws included. Driven by 200 hp AC motor, 1790 rpm, with Powerflight VFD controller. Has 1.155 gear ratio supplying 1200 rpm s...
Hainesport, NJ
Coperian ZSK-18 ML Twin Scrw Extruders New 2008 (3 available)
Coperian ZSK-18 ML Twin Scrw Extruders New 2008 (3 available) Screw Diameter: 18 mm/twin screw 15 HP Centerline – 1100mm/43.3″ Water Cooled 460 volt
Rockville Centre, NY
Trusted Seller
2001 DAVIS STANDARD PEDESTAL
- Manufacturer: Davis-Standard
- Model: PEDESTAL
Used 1.25" Davis Standard Pedestal Extruder With 36/1 L/D Vented Barrel. New 2001. Has electrically heated air cooled barrel, includes temperature control panel and 5 hp AC motor, 230/460 volt. Previously used as...
Hainesport, NJ
Trusted Seller
BATTENFELD-CINCINNATI CM55
- Manufacturer: Battenfeld-Cincinnati
Used Battenfeld-Cincinnati model CM55 counter rotating approximately 55mm diameter twin screw extruder. Conical screw design. Barrel is electrically heated and air cooled in three zones with air blowers with 0.20...
Hainesport, NJ