Used Extruders

3.4″ Davis Std. Extruder (Recently Rebuilt)

• Manufacturer: Davis-Standard

3.4″ Davis Std. Extruder (Recently Rebuilt) 50 HP AC Motor with AC Drive – rated up to 100 HP 24:1 L/D Ratio – Non-Vented Eurotherm Controllers Screw in Good Condition NOTE: Rebuilt and painted 2 years ago, never...

2″ Davis Standard 30:1 – Air Cooled Extruder

• Manufacturer: Davis-Standard

3.5″ Polytruder 24:1 Air Cooled Extruder

6″ Davis Standard 30:1 Extruder

• Manufacturer: Davis-Standard

4.5″ Davis Standard Extruder MV45IN45 1997

• Manufacturer: Davis-Standard

4.5″ Davis Std. Extruder MV45IN45 – New 1998 Water Cooled 24:1 N-Vented

2.5″ Akron/EDS Akron 36:1 Extruder Reconditioned

2.5″ Akron/EDS Akron 36:1 Extruder Reconditioned 42″ Centerline – 36:1 L/D Ratio – 6″ x 3.5″ feed throat, Belt Driven through a 13.95:1 Koellman PEZS 360/3.5 Gearbox, Rated to 125 HP, 75 HP Baldor DC Motor with R...

Aaron Process 300 Gallon Sigma Blade Mixer Extruder. 450 Gallon Total Capacity.

• Manufacturer: Sigma

54118001 Used Aaron Process 300 Gallon Sigma Blade Mixer Extruder. 450 Gallon Total Capacity. Carbon Steel Construction. Serial Number 93300150464MX. Tangential Sigma Blades. Bowl is approximately, 54" front to b...

Pre-Owned Killion KL-075 Single Screw Extruder – Electrically Heated, Air-Cooled

• Manufacturer: KillionKillion

54037006 Used Killion KL-075 Single Screw Extruder. 19.1 mm Diameter screws. 25:1 L/D. Screw speed 12-120 RPM via a gearbox by a 1.1 kW-380 volt/50cycle/3Ph DC motor. 3 housing sections. Electrically heated, air ...

3.5″ Davis Std. 30:1 Air Cooled Extruder

• Manufacturer: Davis-Standard

3 1/2” Davis Standard 30:1 150 H.P. A.C. Air Cooled 350 to 400 # per HR. Material Poly No Clamp Bolt on Front End 17:1 Gear Ratio 100 RPM 5 Barrel Zones 4 Die Zones

Insta-Pro Model 2000 RC Continuous Extruder – 125 HP Motor, High-Capacity Processing

• Manufacturer: Insta-ProInsta-Pro

53147054 Used Insta-Pro Model 2000 RC Continuous Extruder. Rated capacity approximate 1,300 - 3,840 pounds per hour. Includes extruder barrel and main worm shaft assembly. Driven by 125 HP motor. ...

20mm Werner & Pfleiderer Model ZSK20 Co-Rotating Twin Screw Extruder

• Manufacturer: WP
• Model: ZSK20

10151389 Used 20mm Werner & Pfleiderer Model ZSK20 Co-Rotating Twin Screw Extruder. Has 40/1 L/D barrel at 43" centerline height driven through a 3:1 gearbox with a 37-Newton meter torque capacity per screw shaft...

1 1/4″ Davis Standard Extruders (Stripers) 4 Available

• Manufacturer: Davis-Standard

6″ NRM PM III -30:1 VENTED – AIR COOLED EXTRUDER

6″ NRM PM III -30:1 VENTED – AIR COOLED EXTRUDER REBUILT – approximately 43″ centerline height, gearbox having new bearings and seals with cooling system – new heat exhanger and pump, 30:1 L/D 8 zone barrel, cast...