Used Machine Tools in Aichi, Japan

Machine Tool Peripherals/Others/Workpiece Gripper
Chuck: 8 inches If there is any discrepancy between the description and the actual product, the actual product will be given priority.
Toyohashi, Japan
EROWA Tools/ Tools/Manual Clamp Chucks
- Manufacturer: Erowa
Chuck outer diameter: Φ80 mm If there is any discrepancy between the description and the actual product, the actual product will be given priority.
Toyohashi, Japan
Tools/ Tools/V-groove square block
300 x 300 x 300mm If there is any discrepancy between the description and the actual product, the actual product will be given priority.
Toyohashi, Japan
EROWA Tools/ Tools/Manual Clamp Chuck with Block
- Manufacturer: Erowa
Chuck outer diameter: Φ80 mm,. Block dimensions: 80 x 80 x 80 mm In case of any discrepancy between the description and the actual product, the actual product will be given priority.
Toyohashi, Japan
unidentified BT40 Tool
- Manufacturer: unidentified
BT40, Tool 25
Aichi, Japan
NIKKEN BT50-SLO-25-150 Tool
- Manufacturer: Nikken
Side through
Aichi, Japan
Trusco Nakayama / Cabinets, Workbenches / Tool Racks
- Manufacturer: Trasco Nakayama
For BT50,. Holders: 40 pcs. Dimensions: (Width)750(Depth)620(Height)1500mm Number of sections: 8 In case of any discrepancy between the description and the actual product, the actual product shall take precedence.
Toyohashi, Japan
Tools/Vices, Blocks, Clamps/Two-sided Angle Plates
Work surface dimensions: (W) 1000 x (H) 850mm Base dimensions: (W) 820 x (D) 800 x (T) 55mm Base mounting holes: M16, 640mm pitch Total height: 1065mm T-slots: 18mm x 6 (each side) *If there are any discrepancies...
Toyohashi, Japan
Others / Cabinets and Workbenches / [Bid No. 419-421] Tool Stand
For BT50 *If there are any discrepancies between the product description and the actual product, the actual product will take precedence.
Toyohashi, Japan
JAM/Japan Automatic Machine AP100
- Manufacturer: JAM/Japan
Material: SKS,. Hardness: HRC60°,. Dimensions: (D)90*(W)90*(H)100㎜,,, Weight: 2.4kg Weight: 2.4kg In case of any discrepancy between the description and the actual product, the actual product shall take priority.
Toyohashi, Japan
JAM/Japan Automatic Machine TDP150
- Manufacturer: JAM/Japan
Width of the clip: 120 mm, Width of the clip opening: 150 mm, Width of the clip opening: 150 mm Opening width: 150mm, Tilt: 45°, Tilt: 45°, Tilt: 45°, Tilt: 45°, Tilt: 45 Tilt: 45°, Swivel: 360 Swivel: 360°, Tilt...
Toyohashi, Japan
1996 Okamoto Machine Tool PFG-525
- Manufacturer: Okamoto
- Model: PFG-525
T:480*200mm,. Sine bar chuck, (OD)φ180-205*(W)10-20*(ID)φ31.75mm Grinding wheel: (OD)φ180-205*(W)10-20*(ID)φ31.75mm, All manual In case of any discrepancy between the description and the actual product, the actua...
Toyohashi, Japan
2002 Okamoto Machine Tools PSG-52DX
- Manufacturer: Okamoto
- Model: PSG-52
T: 550*200 Table travel: (left/right) 650*(front/back) 230mm Grinding wheel: (outer diameter) φ205*(width) 19*(inner diameter) φ50.8mm *If there are any discrepancies between the product description and the actua...
Toyohashi, Japan
2012 Okamoto Machine Tool PFG-500II
- Manufacturer: Okamoto
- Model: PFG-500
T:600*140mm,. Table travel: (left/right)540*(front/back)180mm, Grinding wheel: (OD)φ160*(W)6-32*(I.D.φ31.75) All manual In case of any discrepancy between the description and the actual product, the actual produc...
Toyohashi, Japan
2007 Okamoto Machine Tool Works IGM-15NC
- Manufacturer: Okamoto
- Model: IGM-15NC
FANUC-18iTB, Grinding hole diameter: 6 to 150 mm dia. Grinding length: 125mm, Swing over table:φ600mm, Swing inside chuck cover:ø260mm, S:X170*Z500mm, Grinding wheel axis ~850rpm, 3-jaw chuck (GAMET 315MAC), Wate...
Toyohashi, Japan