Used Forging

6000mm dia Kaltek Ring Rolling Mill, 80~1100 Ring Height

Additional info: Replacement of PLC Control system, PLC Main panel & Operator's panel to brand new Siemens S7-400 Upgrade of Hydraulic system Replacement of packing and seals Replacement of bearings Current Volta...

1970 1,200 ton Hatebur AMP-70 4-Die, max bar dia

Still installed and under power for inspection Very Good working condition Available for immediate inspection and delivery

1980 440 ton 3-1/2" dia Peddinghaus Caddy 80 Bar

• Manufacturer: Peddinghaus

Additional info: Cutoff capacities at material tensile strengths: Rounds: psi 65,000 - 3.500" psi 92,000 - 3.156" psi 121,000 - 2.750" Squares: psi 65,000 - 3.937" psi 92,000 - 3.562" Flats: psi 65,000 - 7" x 1.3...

1980 1,200 ton National model 6-4 Heavy

• Manufacturer: National

Complete with: Spare parts as follows : (1) Main Electric Motor (2) Adjusting Wedges (1) Upper transfer finger assembly (1) Lower transfer finger assembly (1) Die Block clamping piston This National 6-4 was used ...

3,500mm Asian Built Radial Axial Ring Rolling Mill Re:24925

• Manufacturer: Asian Built

Dia: 3,500 mm | Height: 800 mm | Builder: Asian Built | Radial: 280 tonnes | Axial: 180 tonnes | Min dia: 650 mm | Number of main roll motors, current type & power of each: One DC @ 500kW | Number of axial roll ...

2,800mm Banning RWW H120/V100 CNC

• Manufacturer: Banning

Max Ring diameter - 2,800mm (110") Max Ring height - 500mm (19.7") Radial tonnage - 120 tons Axial tonnage - 100 tons Max Ring Blank weight is 2,000 kg Radial (King) Roll drive power - 315 kW (422 hp) Axial (Edgi...

16,000 ton SMS Horiz Direct Sgl Action Ext Press, Ind Billet

Additional Data: Main cylinder: 13560 MT Side cylinder: 2440 MT Working pressure: 31 MPa Main cylinder dia.:2360 mm Side cylinder dia.: 360 mm x 4 pcs Return force: 10.8 MN (10800 MT) Extrusion stroke: 3700 mm Bi...

Anvil by Trexton

• Manufacturer: Trexton

31" long x 12.5" H, 12" horn, 1" square tool holder, Forged Steel, on home made stand

Ajax Magnathermic 1,650 lb. Ladle

• Manufacturer: Ajax Magnathermic

S# 00296, With hydraulic unit, "Ladle only", Inside pot measurements 16"Round x 28"D, 750 volts 300kw 180hz

HASENCLEVER AWF 400/800/800 W/Automatic Manipulator

• Manufacturer: Hasenclever

AUTOMATIC FORGING ROLL Max Dia of Workpiece: 150mm Diameter of Rolling Segment: 800mm Usable width of middle roll: 800mm Usable width of outer roll: 355mm Roll revolutions (1/min RPM): 30 min~1 Roll Adjustment: 2...

EUMUCO RW1

• Manufacturer: SMS Eumuco
• Model: RW1

FORGING ROLL Max Dia of Workpiece: 55mm Diameter of Rolling Segment: 370mm Usable width of middle roll: 500mm Usable width of outer roll: 160mm Max length of working piece-middle: 570mm Max length of working piec...

AJAX #0

• Manufacturer: Ajax

FORGING ROLL Diameter of Roll: 12-1/2" Standard width roll: 14" Floor space, approx.: 5'8"L-R x 4'2"F-B Weight, approx.: 8,500 lbs

1996 ASAHI OKUMA AT-635

• Manufacturer: Okuma
• Model: AT-635

2 DIE 2 BLOW COLD HEADER * BUSHING CUT-OFF * OSG MONITOR * TIMED POSITIVE KNOCKOUT IN 1ST AND 2ND * WIRE STRAIGHTENER * SOUND ENCLOSURE * LOTS of TOOLING

AJAX 1" UPSETTER

• Manufacturer: Ajax

1" UPSETTER * Air clutch * Air brake **Rebuilt by Ajax in 1979 Including: New Brake, Elec. Controls, Flywheel Brake, Clutch was redesigned (anti-friction bearing replaced old bronze bushing type, Trabon lubricati...

NAZEL 4B 600LBS Blacksmith Power Forging Hammer Pneumatic Self-Contained

���Normal wear from use but that- OVER 30 years ago, and since then- always kept in dry storage. You MUST read the history of it below. Great condition with smooth ram cylinder surface. i.e. not scoring. It will ...