Used Machine Tools in Shizuoka, Japan

Trusted Seller
Auction
SLOPE-BKT-FOR-PC200
Operation Not Confirmed and also not checked Damage and Missing parts Inland Trucking Charge to Yokohama port JPY60,000 Domestic shipping fee to Yokohama port JPY 60,000
Kikugawa, Japan
Visit Auction Website
FUJIGEN CTL-00T
- Manufacturer: Fuji Gen
FUJIGEN Equilateral Triangle 60°/Cartridge for Gut Tender CTL-00T Equilateral triangle 60° tip, shank diameter 18φ, keyway width 4,95mm, overall length 117mm, no back teeth
Hamamatsu, Japan
OSG P5D1500FS20M04
- Manufacturer: OSG
OSG-PHOENIX 15mm/5D type indexable drill P5D1500FS20M04 not opened Blade diameter 15mm, drilling hole depth 75mm, max. drilling diameter 15,8nn, overall length 140mm, shank diameter 20mm, shank length 50mm, 2 bla...
Hamamatsu, Japan
Hitachi Tool ARL3032R
- Manufacturer: Hitachi
Hitachi Tool 32mm / Rapid-Cutting Type Alpha Radius Mill ARL3032R Flat/groove Coarse/medium coarse Cutting edge diameter 32mm, Max. depth of cut 5mm, Shank 32mm, Length under neck 120mm, Total length 200mm, 3 blades
Hamamatsu, Japan
Mitsubishi Materials FSTU212R
- Manufacturer: Mitsubishi
MITSUBISHI MATERIALS Holder for machining of equilateral triangular 60° internal diameter FSTU212R Internal diameter, through-hole/edge face, stop hole, copying, minimum machining diameter 16mm, depth of cut 93°,...
Hamamatsu, Japan
OSG PSE11R030SS32-3L
- Manufacturer: OSG
OSG-PHOENIX 30mm/Shaper Cutter Straight Shank PSE11R030SS32-3L Flat/Side/Groove Rough-Finish O.D. 30mm Max. depth of cut 10mm Shank 32mm Neck 90mm length, 190mm length, 3 blades The package was unopened, but was ...
Hamamatsu, Japan
Tungaloy PSKNR2020
- Manufacturer: Tungaloy
Tungaloy Square 90° OD Turning Holder PSKNR2020 O.D./Edge Cutting Angle 75°Cutting Edge Length 12 Chip Fleece Angle 0°Right Handed Shank 20*20mm
Hamamatsu, Japan
2012 Orii AFC05GAFP
- Manufacturer: Orii
Orii 500mm NC Roll Feeder AFC05GAFP Width: 20mm-500mm, Thickness: 0.2t-3.2t, Top Speed: 1.0m/sec Left → Right
Hamamatsu, Japan
OSG PSE11R030SS32-3L
- Manufacturer: OSG
OSG-PHOENIX 30mm/Shaper Cutter Straight Shank PSE11R030SS32-3L Flat/Side/Groove Rough-Finish O.D. 30mm, Max. depth of cut 10mm, Shank 32mm, Length under neck 90mm, Total length 190mm, 3 blades This was an unopene...
Hamamatsu, Japan
Rhombic 35° OD Turning Holder
- Manufacturer: Tomoe Co. Ltd.
Unknown Rhombic 35° OD turning holder One-round length of the sheet approx. 15,3mm Total length 150mm Shank 25×25 right hand side
Hamamatsu, Japan
Tungaloy PSKNR2525
- Manufacturer: Tungaloy
Tungaloy Square 90° OD Turning Holder PSKNR2525 O.D./Edge face, depth of cut 75°, cutting edge length 12°, chip relief angle 0°, right-hand side, shank 25*25mm
Hamamatsu, Japan
S25RMCLNL12
- Manufacturer: Tomoe Co. Ltd.
Rhombic 80° Internal Diameter Holder S25RMCLNL12 Min. machining diameter 32, 0° relief angle, 95° depth of cut, shank 25, with oil hole, left-hand side, multi-clamp type
Hamamatsu, Japan
2020 Dymac R40
- Manufacturer: Daimaku
DIMAC 400mm NC Roll Feeder R40 Width - 400mm, Thickness - 3.2t, Feed Length 0.01mm - 9999.99mm 80mm Width/3.2t, 200mm Width/2.6t, 300mm Width/1.6t Left to Right
Hamamatsu, Japan
Tungaloy EXN03R025M25
- Manufacturer: Tungaloy
Tungaloy 25mm/screw type high feed cutter EXN03R025M25,0-05-C Open when photographed Flat/groove/inclined cut/vertical Cutting blade diameter 25mm, maximum depth of cut 1mm, shank diameter 25mm, length under neck...
Hamamatsu, Japan
CERADEX PVPNR2020K-16Q
- Manufacturer: CERADEX
CERADEX Rhombic 35° OD Turning Holder PVPNR2020K-16Q O.D., end face, copying, depth of cut P:117,5°, cutting edge length 16°, chip relief angle 0°, right-hand side, shank 20*20mm
Hamamatsu, Japan