Used Machine Tools in Shizuoka, Japan

2012 Orii AFC05GAFP
- Manufacturer: Orii
Orii 500mm NC Roll Feeder AFC05GAFP Width: 20mm-500mm, Thickness: 0.2t-3.2t, Top Speed: 1.0m/sec Left → Right
Hamamatsu, Japan
OSG PSE11R030SS32-3L
- Manufacturer: OSG
OSG-PHOENIX 30mm/Shaper Cutter Straight Shank PSE11R030SS32-3L Flat/Side/Groove Rough-Finish O.D. 30mm, Max. depth of cut 10mm, Shank 32mm, Length under neck 90mm, Total length 190mm, 3 blades This was an unopene...
Hamamatsu, Japan
Rhombic 35° OD Turning Holder
- Manufacturer: Tomoe Co. Ltd.
Unknown Rhombic 35° OD turning holder One-round length of the sheet approx. 15,3mm Total length 150mm Shank 25×25 right hand side
Hamamatsu, Japan
Tungaloy PSKNR2525
- Manufacturer: Tungaloy
Tungaloy Square 90° OD Turning Holder PSKNR2525 O.D./Edge face, depth of cut 75°, cutting edge length 12°, chip relief angle 0°, right-hand side, shank 25*25mm
Hamamatsu, Japan
Hitachi Tool ASR
- Manufacturer: Hitachi
Hitachi Tool 32mm/Alpha High Feed Radius Mill ASR ASRS2032R-5 Flat/groove Coarse/medium coarse Cutting edge diameter 32mm, Max. depth of cut 2mm Shank 32mm, Length under neck 70mm, Total length 150mm, 5 blades
Hamamatsu, Japan
Hitachi Tool AR
- Manufacturer: Hitachi
Hitachi Tool 32mm / Rapid-Cutting Type Alpha Radius Mill AR ARS3032R Flat/groove coarse/medium coarse Cutting edge diameter 32mm, maximum depth of cut 5mm, shank 32mm, length under neck 70mm, total length 150mm, ...
Hamamatsu, Japan
Hitachi Tool ASR
- Manufacturer: Hitachi
Hitachi Tool 32mm/Alpha High Feed Radius Mill ASR ASRS2032R-5 Flat/groove Coarse/medium coarse Cutting edge diameter 32mm, Max. depth of cut 2mm Shank 32mm, Length under neck 70mm, Total length 150mm, 5 blades
Hamamatsu, Japan
Kyocera 21mm/MCSE Type Chamfer End Mill MCSE106
- Manufacturer: Kyocera
Kyocera 21mm/MCSE Type Chamfer End Mill MCSE106 Groove/Chamfer Angle 45° Shank 20mm, Head Length 41mm, Total Length 121mm, 1 Flute
Hamamatsu, Japan
OSG P5D1500FS20M04
- Manufacturer: OSG
OSG-PHOENIX 15mm/5D type indexable drill P5D1500FS20M04 when photographed Blade diameter 15mm, drilling hole depth 75mm, maximum drilling diameter 15,8nn, total length 140mm, shank diameter 20mm, shank length 50m...
Hamamatsu, Japan
Tungaloy TID220F25-5
- Manufacturer: Tungaloy
Tungaloy 22,9mm/head interchangeable drill TID220F25-5 unopened Diameter 22-22,9mm, shank diameter 25mm, shank length 56mm, groove length 114mm, total length 200mm This item is unopened. Only the first photo show...
Hamamatsu, Japan
Tungaloy TID220F25-5
- Manufacturer: Tungaloy
Tungaloy 22,9mm/head interchangeable drill TID220F25-5 Open when photographed Diameter 22-22,9mm, shank diameter 25mm, shank length 56mm, groove length 114mm, total length 200mm This was an unopened item, but was...
Hamamatsu, Japan
MITUBISHI AJX12R-403SA32S
- Manufacturer: Mitsubishi
MITSUBISHI MATERIAL 40mm/Interchangeable cutting edge end mill AJX12R-403SA32S Cutting edge diameter 40mm, cutting edge diameter 28.3mm, shank diameter 32mm, overall length 150mm, 3 blades
Hamamatsu, Japan
OSG-WALTER F2042-25
- Manufacturer: OSG-WALTER
OSG-WALTER 25mm/Throwaway End Mill F2042-25×SS20 Cutting edge diameter 25mm, shank 20mm, total length 134mm, 2 blades
Hamamatsu, Japan
Kyocera MCSE106
- Manufacturer: Kyocera
Kyocera 21mm/MCSE Type Chamfer End Mill MCSE106 Groove/Chamfer Angle 45° Shank 20mm, Head Length 41mm, Total Length 121mm, 1 Flute
Hamamatsu, Japan
MITUBISHI AQXR172SN16S
- Manufacturer: Mitsubishi
Mitsubishi Materials 17mm/Hybrid Mill AQXR172SN16S Flat/side rough/medium rough Cutting edge diameter 17mm, maximum depth of cut 7.4mm, shank 16mm, length under neck 30mm, total length 120mm, 2 blades
Hamamatsu, Japan