Used Roll Formers in Massachusetts, USA

8 Station Dual Head Cleat Former for Duct Lines

In brief Ductformer’s Model CR8-CF-DH Dual Head Cleat Former forms the Drive Cleat Flange on both ends of the Duct in a single pass through operation. The System overall can be incorporated into any existing Duct...

TK 16 Ga. Pitts. (Choice of Opposing Rolls)

• Manufacturer: Pitts

The 16 gauge Pittsburgh Lock machine has 7 forming stations with 2 forming positions. One position forms the Pittsburgh Lock, while the outboard position has the ability of forming a number of other profiles, to ...

TK No. 24 Cheek Bender (2 Sided)

Available from a distributor near you. Normally in stock in one of our warehouses. For real production! This beefy little 24 inch, two sided cheek bender is built to last. Bench mounted, this machine comes ready ...

Flagler 12 Station Lockformer TDC Machine

• Manufacturer: Flagler

Extended Shafts for Auxiliary Tooling Features: 12 Forming stations with Adjustable Feed table for dual TDC Forming when forming TDC Flange on opposing side of duct work 1-1/2″ Dia.(At Bearing) Hardened and Groun...

CR8 Auto Feed Rollform System

The Automated CR8-SDC Auto Feed Rollform System is designed to feed and form the Flat ’S’ and Drive Cleats on the inboard Rolls directly from coil stock. The Automated System consists of a Dual Station Coil Cradl...

CR8-CF Cleat Former

You will notice the quality of the CR8-CF Cleat Edge Former as soon as you turn the power on. The quietness while running reveals the precision workmanship and superior design to provide years of dependable servi...

CR8-CF-DH Dual Head Cleat Former

In brief Ductformer’s Model CR8-CF-DH Dual Head Cleat Former forms the Drive Cleat Flange on both ends of the Duct in a single pass through operation. The System overall can be incorporated into any existing Duct...

12 & 14 Station TDFC Dual Head Rollformer for Duct Lines

• Manufacturer: Ductformer
• Model: TDFC

The TDFC Flange application has proven to be the most cost effective method to construct and install commercial rectangular ductwork. The C-Style Flange provides the extra strength and rigidity to sustain the Air...

RAMS-2007 20ga Stand Alone Power Flanger

• Manufacturer: Rams

This unit comes mounted in a heavy duty cabinet. The RAMS-2007 Power Flanger will form a 7/32″ right angle flange on either straight or curved pieces. It has an adjustable “auto guide” which can be set to automat...

TK 24 Ga. Pitts. with Stand

• Manufacturer: Pitts

On the job site or in the shop, this portable little rollformer is a work horse for 24 gauge and lighter material. It is available with power flanging attachment and is perfect for field use. Steel stand include...

Morlin Model 2400 with Power Flanger

Capacity,Speed.Motor,Housing,Dimensions,General 24 to 28 gauge material. 35 fpm. Energy efficient, 1/2 H.P., 115/208-230V, 5.4 AMPS, 60 cycle, single phase, A.C., 1800 R.P.M., Auto over-load protector. Heavy gaug...

Drive Turn Hemmer

• Manufacturer: Flagler

Rollform your drive turn hems on this machine after notching and prior to bending into L or full wrap sections. Simple select the sections to be hemmed with the selector switch and run through. The machine will...

TK T-D-P Roll Former (w/TDP & Clip Rolls)

(Produces either TDC or TDF flanges). At last, an affordable, full service, high quality transverse duct connector machine!!! This 14 station roll former comes standard with TDC or TDF Rolls, Slitter and Clip Rol...

12 & 14 Station TDFC Dual Head Rollformers

Ductformer’s Dual Head TDFC Rollformer is designed for installation in existing Duct Coil Lines or can be used as a Free Standing Unit. The Rollformer is designed to accept and form either the F-Style (CR14-TDFC)...

TK No. 24 Collar Maker

Capacity: 24-30 Gauge Speed: 30ft./minute Notch,bead,crimp and roll complete round starting collars, 3″ to 14″ in diameter out of 24 to 30 gauge galvanized – in seconds, not minutes and with only one pass! Just c...