Building Filters
QTY (2) 80" (2032 MM) WIDE BLISS 4 HI MILL STAND HOUSINGS
- Manufacturer: Bliss
Inventory id: 10971000000
Pittsburgh, PA- Trusted Seller
Keith Machinery Corp Mill Roller (Mill) 5 X 12
- Manufacturer: Keith
Keith, model 5" x 12", piped, variable speed, dispersion mill. Roll dimensions: 5" diameter x 12" long. Rates dependent on materials, application and machine configuration . Equipped with 2 hp drvie, chain safety...
Carol Stream, IL - Trusted Seller
ALPINE ULTRAPLEX 500 UP CROSS FLOW HAMMER MILL
- Manufacturer: Alpine
One (1) Used Alpine 500 Ultraplex Cross Flow Hammer Mill Three available, pricing is for one unit unless otherwise noted Used for pulverizing opening out & fiberizing of materials up to a hardness of 3.5 accordin...
Wisconsin, USA - Trusted Seller
Princeton Junction, NJ 
CALIFORNIA PELLET MILL CONDITIONER 17333
- Manufacturer: California Pellet Mill
One (1) California Pellet Mill conditioner for use with a pellet mill. Mixing section measures approximately 28″ in diameter x 8′ long. Unit is belt driven by approximately a 15 HP motor through a gear reducer
Elk Grove Village, IL
XRD-Mill McCrone
The XRD-Mill McCrone was specially developed for the preparation of samples for subsequent X-ray diffraction (XRD). The mill is used for applications in geology, chemistry, mineralogy and materials science, quali...
Clifton, NJ- Trusted Seller
Carbon Steel Ball Mill - IPP# 97152
conical ball mill Non drive end ID= approximately 470 mm, (measured at the most narrow point) Drive end ID is approximately 465 mm. belt driven by motor via bull gear
Princeton Junction, NJ - Trusted Seller
Hammer Mill, C/S, 75 HP
Hammer Mill, C/S, 75 HP Used hammer mill, carbon steel construction, 16" x 18" feed opening, on base with 75 hp motor.
New Jersey, USA - Trusted Seller
Fitzpatrick Mill Roller (Mill) 20"L X 9"D
- Manufacturer: Fitzpatrick
Fitzmill, Model 20, guiloriver, prebreaker with pounds of product per hour – depending on materials and application. Equipped with stainless steel contact parts and 21" x 40" product feed throat with 94" charge h...
Carol Stream, IL - Trusted Seller
12in Dia. x 16in Long Batch Mill
4.75in x 6in Door Accepts 16in Rods or Balls Variable Speed Drive Unit Welded 3/8in Thick Construction Axle is Drilled Through 0.25in New Pillow Block Ball Bearings Mill and Motor Mounted to Common Angle Iron Fra...
Northeastern United States, USA - Trusted Seller
Ball Mill Carbon Steel - IPP# 79105
- Manufacturer: Blaw Knox
CS/Ni-hard lined 650 deg F. 2"-6" CS ball charge Gear driven by 40 HP, 3/60/220/440 volt thru Falk gear reducer, ratio 32.69:1. Bull and pinion gear ratio 4.85:1. Unit has Manzel fully centralized lubrication sys...
Princeton Junction, NJ - Trusted Seller
Ball Mill Carbon Steel - IPP# 97153
- Manufacturer: Hardinge
conical balls. Belt driven by motor via bull gear. Non drive end ID= approximately 470 mm, (measured at the most narrow point) Drive end ID is approximately 465 mm.
Princeton Junction, NJ - Trusted Seller
Ball Mill Carbon Steel - IPP# 79104
- Manufacturer: Blaw Knox
650 deg F. 2"-6" CS ball charge Gear driven by 40 HP, 3/60/220/440 volt, Phila gear reducer ratio 30.6:1. Bull and pinion gear ratio 4.85:1. Unit has Manzel fully centralized lubrication system w/6-station Manzel...
Princeton Junction, NJ - Trusted Seller
Princeton Junction, NJ - Trusted Seller
Ball Mill Carbon Steel - IPP# 97154
- Manufacturer: Hardinge
conical ball belt driven by motor via bull gear Non drive end ID= approximately 470 mm, (measured at the most narrow point) Drive end ID is approximately 465 mm.
Princeton Junction, NJ