Used sheets

Evans Midwest LT4280 Layup Table/ Indexing Table + Motorized Laminate Rack

• Manufacturer: Evans

Evans Midwest has a NEW updated LT4280 Layup Table and it is available with a NEWLY designed Motorized Laminate Rack. This is the most cost effective option in all of North America! (*Note: Unit is shown with the...

DAVIS STANDARD 48"

• Manufacturer: Davis-Standard

Used Davis Standard sheet take-off unit consisting of (3) 48" face rolls mounted in a vertical arrangement for a downstack operation. All three rolls measure 16" in diameter. Top roll is tungsten and the middle a...

MARSHALL & WILLIAMS 54" Wide

• Manufacturer: Marshall

Used Marshall and Williams sheet take-off unit consisting of (3) 54" face rolls mounted in a vertical arrangement for a downstack operation. All three rolls measure 16" in diameter and are ceramic coated. Top and...

1997 BROWN MACHINE SR-2525

• Manufacturer: BROWN MACHINE

Specifications Servo Indexing? Yes Controller Make and Model: Operator control console houses the Thermoforming Control SYSCOM II. RS-232 serial communications. Alan Bradley PLC, Indramat amplifier, Indramat IAE ...

Graphite Milling Block Bulk Chunks High Density Carbon 1250 Lbs.

Die Pressed Artificial Graphite Block with High Density High Purity Die Pressed Artificial Graphite Block This is a bulk listing of graphite blocks that were used as a cast mold. Various size pieces in the skid. ...

2010 BROWN MACHINE CS-5454

• Manufacturer: BROWN MACHINE

CS-5454 T-454LS 20" x 54" 508mm x 1372mm Length: 54.0 in | Width: 54.0 in | Maximum mold size (width x length): 54" x 54" 1372mm x 1372mm | Maximum holding force: 150 tons or 260 tons 1339 kn or 2321 kn | Maximum...

2025 FORMECH 508DT

• Manufacturer: FORMECH

Max Depth of Draw / Max Tool Height (mm/inches): 185 / 7.3 Max Material Thickness (mm/inches): 6 / 0.25 Single Phase Power Requirements: 208-240V / 13A Pump Flow (SCFM @ 0 in. / 60Hz) (Pump flow m3 /h @ 0mbar / 5...

EDI 60"

• Manufacturer: EDI
• Model: 60

Used 60" EDI Flexible sheet die. Serial #75-2023. Has an upper flexible lip, fixed lower lip, and approximately a 3/4" back center fed entrance.

2008 EDI 52 U/F R75

• Manufacturer: EDI
• Model: 52 UF R75

Unused 52" EDI dual entry sheet die. Model 52 U/F R75, serial #08-27852, new 2008. Equipped with restrictor bar and poly side control.

EDI H75

• Manufacturer: EDI
• Model: H75

Used 18" wide EDI Model Ultraflex H75 Sheet Die. Serial number 88-11898. Has fixed bottom lip, no restrictor bar. Equipped with circular 2" diameter center back inlet.

Dieboard EVA Foam Sheet Ejection Sponge for Die Cutting Machine

• Manufacturer: Rino

Product Introducction: Used for the production of flatbed die cutting plate, installed on the die cutting plate for the ejection of waste paper scraps from cardboard boxes after die cutting. It is essential for ...

EDI Ultraflex H40

• Manufacturer: EDI

Used EDI 28.5" Ultraflex H40 sheet die. .001-.040 lip opening, 240 volt 350 watt heaters. 1.25" diameter rear material entry. Mounted on 41" centerline V-caster stand. Manufactured 4/1989. Serial #89-12354.

EDI H-40

• Manufacturer: EDI
• Model: H-40

Used 49" wide Extrusion Dies Inc sheet die. Model H-40, serial #97-19250. , new 1997. Has upper flexible lip and fixed removable lower lip. Center back feed entrance. Unit set up for (5) zones of temperature cont...