Used Pines Machine Tools

1995 Pines 3T

• Manufacturer: Pines
• Model: 3T

dial -a - bend programable control electrical controls hydraulic system

1964 PINES 15 #0106117

• Manufacturer: Pines
• Model: 15

SPECIFICATIONS: EQUIPPED WITH: Run Out w/Target 2′ W x 6′ L x 5′ High BIJUR Lube System End Cropping NOTE: Rebuilt Controls, PLC OVERALL DIMENSIONS: 4′ 6″ W x 6′ L x 4′ High APPROXIMATE WEIGHT: 10,000 Lbs.

PINES 3/4 #0101717

• Manufacturer: Pines
• Model: 34

MACHINE SPECIFICATIONS: EQUIPPED WITH: (6) Station Automatic Turret Degree of Bend Selector Pressure Die Holder BIJUR One-Shot Slide Lubricator Swinging Arm Safety Device 5 HP AC Main (Pump) Drive Motor; Electric...

PINES #3/4 #0101617

• Manufacturer: Pines
• Model: 34

MACHINE SPECIFICATIONS: Panel Mounted Hydraulic Valves Oil Reservoir in Base EQUIPPED WITH: Stationary Mandrel Rod & Holder Manual (8) Station Turret Degree of Bend Selector Pressure Die Holder; Clamp Die Holder ...

PINES 160834G.O

• Manufacturer: Pines

5HP HYDRAULIC MAIN MOTOR 3/4" CAP ,1966 , SCH 80 AUTO LUBE AUTO TURRET DEGREE STOP FLOOR PENDENT CONTROL 220VOLT 3 PH

PINES 1-1/4 #0641823

• Manufacturer: Pines
• Model: 1-14

Round tubing(non ferrous): 2.5" X 109" | Round tubing(mild steel): 2.5" X .065" | Shcedule 80: 1.5" | Maximum bending radius: 12" | Maximum bend angle: 200 DEGREES | Maximum tube length over mandrel: 89" | Bendi...

PINES 1-1/4 #0641723

• Manufacturer: Pines
• Model: 1-14

Round tubing(non ferrous): 2.5" X 109" | Round tubing(mild steel): 2.5" X .065" | Shcedule 80: 1.5" | Maximum bending radius: 12" | Maximum bend angle: 200 DEGREES | Maximum tube length over mandrel: 89" | Bendi...

Pines Rotoform Dies #1802113T

• Manufacturer: Pines

SPECIFICATIONS:

3/4" Pines Tube Bender 28011G

• Manufacturer: Pines

NON-FERROUS TUBING 1 ½" OD x .065 WALL STEEL TUBING 1-3/8" OD x .065 WALL EXTRA HEAVY PIPE ¾" STAINLESS STEEL TUBING 1-1/8" OD X .065 WALL STEEL BAR-ROUND ¾" DIAMETER MAX. RADIUS-STANDARD 10" MAX. RADIUS-EXTRA 18...

1967 PINES Roto Form 5-12, Seri #1802113

• Manufacturer: Pines
• Model: ROTO FORM 5-12 SERI

SPECIFICATIONS: 12" Pines Roto Form 5-12 Roll Extrusion Bending Machine Maximum Radius (practical limit).........: 120" Minimum Radius (to centerline)...........: 3" x OD Cycle to 90� on 3D Centerline Radius........

1967 PINES Roto Form 5-12, Seri #1802513

• Manufacturer: Pines
• Model: ROTO FORM 5-12 SERI

3" #2 PINES HORIZONTAL TUBE BENDER 16022D

• Manufacturer: Pines

MODEL #: 2 SERIAL #: 11235-83132 3" CAPACITY COUNTER CLOCKWISE BENDING HEAD 8 POSITION TURRET STOP 200º ROTATION MANDREL EXTRACTOR HYDRAULIC PUMP CONTROL PANEL MOTOR: 2 HP

Pines bendpro

• Manufacturer: Pines

Round Tubing Bending Capacity (Mild Steel): 6″ x 0.165″ Round Tubing Bending Capacity (Stainless): 4- 1/2″ x 0.250″ Square Tubing Bending Capacity (Mild Steel): 4″ x 0.250″ 220/480 Volt, 60 Hz, 3 Phase Electrics