Used plc

Trusted Seller
300 LB/HR Maag Melt Pump, LS-45-1053A Melt Pump, 5 HP
- used
- Manufacturer: Maag
Used 300 LB/HR Maag Melt Pump, LS-45-1053A Melt Pump, 5 HP Ac Motor 3 Temperatue Control Zones Yaskawa AC Drive Dual Pressure Readouts. Amp Gauges For Each Heating Zone, Has PLC Control 230 Volt On Casters With L...
United States
Trusted Seller
12" Single Screw Crown/CDL Dump Extruder, Model RPU2E400, 10:1 L/D Ratio
- used
- Manufacturer: Crown
30" L x 12" W Water Cooled Feed Throat With Pneumatic Ram Stuffer Water Cooled Screw, 4 Downstream Zones, Non-Vented Closed Loop System With Pump, Tank, And Heat Exchanger Approximate 48" Centerline Height 500 V...
United States
Trusted Seller
12" Single Screw Crown/CDL Dump Extruder, Model RPU2E400, 10:1 L/D Ratio
- used
- Manufacturer: Crown
30" L x 12" W Water Cooled Feed Throat With Pneumatic Ram Stuffer Water Cooled Screw, 4 Downstream Zones, Non-Vented Closed Loop System With Pump, Tank, And Heat Exchanger Approximate 48" Centerline Height 500 V...
United States
Trusted Seller
0.8 in. WELDING ENGINEERS TWIN SCREW EXTRUDER – 34:1 L/D
- used
- Manufacturer: Welding Engineers
1 – used .8 in. Welding Engineers Twin Screw Extruder. Model HT0.8. With counter rotating tangential screws. Barrel with (7) sections including (2) vented and plugged sections and (1) vented section. Electrically...
USA
Trusted Seller
3.5" Cincinnati Milacron Side Feed (MuCell) Extruder, 30:1 L/D Ratio, 75 HP
- used
- Manufacturer: Cincinnati
Used 3.5" Cincinnati Milacron Side Feed Single Screw Extruder Model Apex 3.5 30:1 L/D Ratio, 30:1 L/D Special Screw for MuCell Material Side Port Feed Throat for MuCell Material Entry Water-Cooled Barrel 6 Barrel...
United States
Trusted Seller
18mm Leistritz Micro-18 Co-Rotating Twin Screw Extruder
- used
- Manufacturer: Leistritz
Used 18mm Leistritz Micro-18 Co-Rotating Twin Screw Extruder 500 RPM Screw Speed 6 Barrel Segments, Top Ports In Segments 1, 2, and 6 6 Barrel Zones Controlled By Eurotherm 808 Temperature Controllers Lenze 2.3 K...
United States
Trusted Seller
850 LB/HR Eagle Pipe Extrusion Line Capable Of Making Pipe Up To 24” Diameter, 2018
- used
- Manufacturer: Eagle
850 LB/HR Eagle Pipe Extrusion Line Capable Of Making Pipe Up To 24” Diameter New In 2018 Model PE-620 Polyethylene Pipe Line 90MM SJ90/30 Primary Extruderm L/D Ratio, 2 HP AC Motor Die And Mandrel 19’ Vacuum Coo...
United States
Trusted Seller
66" Wide Cincinnati Milacron Horizontal Sheet Line Downstream, New In 2012
- used
- Manufacturer: Cincinnati
Used 66" Wide Cincinnati Milacron Horizontal Sheet Line Downstream, New In 2012 66" Wide x 12" Diameter Rolls Hydraulic Roll Pressure 4.55 FPM Line Speed Oil Heated/Cooled Rolls (3) 48KW, Sterling Hot Oil Heaters...
United States
Trusted Seller
80" Wide Davis Sheet Line With 5"(130MM) 34:1 Extruder, New In 2009
- used
- Manufacturer: Davis-Standard
Maguire WSB-940T Gravimetric Blender 5 inch (130 mm), 34:1 L/D, Thermatic III, 13.85:1 Gearbox Ratio, Model 130MM45T, Water Cooled, 8 Barrel Zones, Vented Barrel, 300 HP (222 KW) AC Drive System, Yaskawa Drive, S...
United States
Trusted Seller
66" Davis Standard/Mega Coex Sheet Line With 4.5" and 2.5" Extruders
- used
- Manufacturer: Davis-Standard
66" Wide Sheet Line Consisting Of The Following Pieces: 4.5" Davis Standard 45IN45 Extruder, 32:1 L/D Ratio, 17.49:1 Gearbox Ratio, 300 HP 1788 RPM Marathon AC Inverter Duty Motor(NEW IN 2016) And Mitsubishi Driv...
United States
Trusted Seller
Erema Intarema Model 1714 TVEPLUS Econ Save 5" Approx. Extruder, (New 2020), 1250-Min - 1550-Max
- used
- Manufacturer: Erema
Erema Intarema Model 1714 TVEPLUS Econ Save 5" Approx. Extruder, (New 2020), 1250-Min - 1550-Max PE-LD Capacities, with PLC Controls, Multiple Heat Zones, Ultra Fine Filtration Filters and Die, Spinner Dryer, Sep...
Modesto, CA
Trusted Seller
Erema Intarema Model 1714 TVEPLUS Pelletizing Line, Econ Save 5" Approx. Extruder, (New 2020),
- used
- Manufacturer: Erema
Erema Intarema Model 1714 TVEPLUS Pelletizing Line, Econ Save 5" Approx. Extruder, (New 2020), 1250-Min - 1550-Max PE-LD Capacities, with PLC Controls, Multiple Heat Zones, Ultra Fine Filtration Filters and Die, ...
Modesto, CA
Aasted Discover the Aasted Alice™ Compact
- new
- Manufacturer: Aasted
The Alice™ C-Frame is a versatile depositor and extruder, perfect for small-scale production and laboratory environments. Designed to gently handle any type of mass, this machine allows you to work with up to thr...
Farum, Denmark
Trusted Seller
DAVIS STANDARD 100 MM
- used
- Manufacturer: Davis-Standard
Used temperature control panel previously used with 100mm Davis Standard extruder. No temperature instruments included. Previously used with PLC for temperature input.
Hainesport, NJ
Trusted Seller
DAVIS STANDARD 100 MM
- used
- Manufacturer: Davis-Standard
Used temperature control panel previously used with 100mm Davis Standard extruder. No temperature instruments included. Previously used with PLC for temperature input.
Hainesport, NJ