Used Extruders in New York, USA

2.5″ NRM 24:1 Extruder

2.5″ NRM 24:1 Extruder 75 HP AC Motor with Magnetek AC Inverter. Air Cooled

AET 10/6″ Dual Diamter Extruder

AET dual diameter 10″-6″ – 32:1 L/D 50” centerline height film reclaim extruder with Koellmann gear double reduction gear reducer, with oil pump, heat exchanger cooling system, cast water cooled feed throat with...

1″ Akron 24:1 Extruders (2 available) Rebuilt

1″ Akron 24:1 Extruders – Rebuilt (2 available) photos shown are in the middle of the rebuild….will show photos upon completion – can accept PO now with small deposit…

3/4″ Akron Extruder Model M Pack

3/4″ Akron 24:1 Extruder Model M Pack – new 1994 24:1 – L/D 2 Barrel and 2 Die Zones – 2 HP AC Motor & Drive

Rebuilt 6″ NRM Plastics 30:1 Extruder

Rebuilt 6″ NRM Plastics 30:1 Extruder 6″ NRM Plastics Extruder – Rebuilt- approximately 43″ centerline height, gearbox having new bearing (less thrust) and seals with cooling unit, heat exchanger, pump and motor,...

2.5″ Crown 36:1 Extruder – 2015

• Manufacturer: Crown

2.5″ Crown 36:1 L/D Extruder – 2015 Expected Rate: 10-200 Kgs/hr. Extruder Specification: 2.5” Dia., 36:1 L/D Ratio Barrel Centerline: 40″ Horsepower: 75HP Drive: AC Screw RPM: 140 Max PSI: 10,000 # of Barrel Zon...

4.5″ Sterling 30:1 Vented Extruder

• Manufacturer: Sterling

3.5″ Davis Standard Extruder Mdl. DS35

• Manufacturer: Davis-Standard

3.5″ Davis Standard Mdl. DS35 Extruder

Black Clawson 6XTR – 6″ Single Screw Extruder

• Manufacturer: Black Clawson

Black Clawson 6XTR – 6″ Single Screw Extruder Side Port Feed Extruder

3.5″ NRM PM IV 32:1 Extruder

• Manufacturer: NRM

3.5″ NRM PM IV 32:1 Extruder

4.5″ Gloucester HighBoy 30:1 Vented Extruder

4.5″ Gloucester High Boy 30:1 Vented Extruder

92 mm Jinhu Twin Screw Extruder for PE

92 mm Jinhu eTwin Screw Extruder 150 HP, 480 volt with a ABB drive 1- Spare Distributor gear box 1-Spare Reduction gearbox 1288 running hours COMPLETE – THIS EXTRUDER WAS PROCESSING PE

2.5″ Sterling 30:1 Extruder – New 1995

• Manufacturer: Sterling

2.5″ Sterling 30:1 Extruder Electrically heated, air cooled, 5 Barrel zones, 50 HP DC motor with SCR, with Una-Dyn hot system Model 200

65 mm Jinhu Twin Screw Extruder for PE

65 mm Jinhu Twin Screw Extruder 50HP,480 volts with a ABB drive 1- Spare Distributor gear box 1-Spare Reduction gearbox

1″ Killion Pedestal 30:1 Air Cooled Extruder

1″ Killion Pedestal 30:1 Air Cooled Extruder