Used process engineering in Canada

Warman sump-pump

• Manufacturer: Warman

Warman sump-pump, mod. V15F03, 20 hp c/w valves

Conc jet pump system incl.: (5) 6 mm rubber lined hoppers

• Manufacturer: JET

Conc jet pump system incl.: (5) 6 mm rubber lined hoppers, (1) Eriez vibratory feeder, valves c/w (2) Warman centrifugal pumps, mod. 75WBH, 100 hp ea. (2nd Loc. Red Zone, Level M)

UV-IR infra-red/UV dryer

UV-IR infra-red/UV dryer, ser. no. 11070 (2015) w/ Eriez feeder, infeed and outfeed chutes c/w Kason vibratory separator, ser. no. M-1047, 1/3 hp

Knelson KC-CVD32 Gold Centrifugal Concentrator

Continuously Variable Discharge Automated Controls Knelson ICS Independent Control System, See General Specs Below

Denver No. 18 Special Flotation Cells

• Manufacturer: Denver

Manual Cell to Cell Flow Control Gate Naturally Aspirated Sealed Standpipe

Holman-Wilfley 8000SD Concentrating Table

• Manufacturer: Holman-Wilfley Ltd

Capacity: Up to 2,500 kgs/Hour (Particle Size Dependent) | Deck type: Single Deck | Deck area: 7.5m² | Deck size: 1,600mm x 4,900mm | Water supply requirements: 20 - 35L/min | Drive: Baldor Electric Motor | Powe...

Neffco Centrifugal Bowl

• Manufacturer: Neffco

With Feed Trough Electrical Requirements: Overall Dimensions:

Mill, Sag, 38' X 25'5", Metso, 26,016 HP, Unused #D739643

• Manufacturer: Metso

Unused Metso sag mill, 38' (11.58 m) diameter x 25' 5" (7.76 m) long, 26,016 HP (19,400 kw) Siemens wrap around drive motor-operating frequency 50/60 Hz. EGL: 22' (6.7 m), mill speed: 7.5-10.08 RPM. Maximum volum...

Mill, Sag, 40' X 25', FL Smidth, 34,866 HP, Unused #D739644

• Manufacturer: FL Smidth

Unused FL Smidth SAG mill, 40' diameter x 25' length, designed for 34,866 HP (26,000 kW) wrap-around GMD motor (motor not included). No liners included.

Mill, SAG, 32' x 12', Hardinge-Koppers, 6800 HP Dual Drive #D744636

• Manufacturer: Hardinge

32' x 12' SAG mill, manufactured by Hardinge-Koppers, driven by dual GE 3400 HP 4000 V, 60 Hz AC wound rotor induction motors, model 108770. Complete with trunnions, trunnion liners, girth gear, pinion assemblies...

Mill, Sag, 13'6" X 4', Marcy, No Motor, #D739647

• Manufacturer: Marcy

Marcy Dry Grind SAG Mill, 13' 6" Diameter x 4' Long. Includes bull gear, pinion gear, large Falk gearbox, air clutch, and lube set. No motor. Manufactured new in 1988.

Screening Gold Wash Plant System

Two hydraulic driven screen decks. hydraulic drive clay emulsifier system. Deutz KHD 211 hp diesel generator. 120/208 volt, 3 phase, 38 amps. Air cooled. Four hydraulic pumps off back - Rucker Products. Four hydr...

Hy-G Concentrators

Efficiently accepts a courser than industry standard feed size of -6mm (approx. -¼”) Bowl design that allows for longer ore retention time in the rings and better processing and recovery of fine gold. Extended co...

Knelson KC-CVD32 Centrifugal Concentrator

Continuous variable discharge. Fully automated control system. 40 hp baldor electric motor. Includes guarding, piping package, and spec sheet.

(New) Hy-G HR16 Concentrator with Deep Bowl Technology

• Manufacturer: Hy-G Concentrators Inc.

Recovering free gold and other heavy metals and minerals in crushing, milling, or recycling circuits. Reprocessing crushed and milled tailings to remove gravity recoverable gold and other heavy metals and minerals.