Machine Tools » Saitama

Building Filters

16

Used sheets in Saitama, Japan

2008 Morioka General-purpose vendor [LD-412].
- Manufacturer: Morioka (ciudad)
Product name: Other sheet metal vendors | Main specifications: Universal bending machine, processing plate thickness t2.5x1220mm, mouth opening 38mm, SN:007050378
Tokigawa, Japan
1999 ISEL BS-BH3000 (4 rolls)
- Manufacturer: IJssel
Product name: Roll Bender | Main specifications: Machine weight: 19.8t (including steel plate) Roll shaft effective width: 3000 Upper roll shaft diameter: φ400 Lower roll shaft diameter: φ240 Side roll shaft dia...
Tokigawa, Japan
2014 Amada Miyachi ML-7320CL
- Manufacturer: Amada
Product name: Laser processing machine | Main specifications: 3D head marking area 120mm Protection glass φ40×1t Single phase 100V Software: LMDraw6-3D Air cooled Fiber length 2m Oscillator output 20W
Tokigawa, Japan
Miyachi Technos ML-4141B
- Manufacturer: Technos
ML-4141B Product name: Fusing machine accessories | Main specifications: ML-4141B
Tokigawa, Japan
Taiyo Engineering PB-M25 (Pipe Bender)
- Manufacturer: Taiyo Engineering
Product name: Pipe bender | Main specifications: Manual clamp Maximum bending capacity: φ25x1.6t φ21.7x2.8t Bending radius standard range: R25 to R100 Bendable angle: 5 to 180
Tokigawa, Japan
1997 AMADA 2.0m hydraulic bender [RG-50
- Manufacturer: Amada
- Model: RG-50
- Stroke length: 150 mm
- Throat depth: 315 mm
Product name: Hydraulic bender | Main specifications: 50t×2000 DH：370
Tokigawa, Japan
2000 AMADA [2.0m hydraulic bender]FBD8020NT
- Manufacturer: Amada
- Model: FBD-8020NT
Product name: Hydraulic bender | Main specifications: NC capacity 80t, table 2000mm, stroke 150mm, upper and lower hydraulic clamps, pressure capacity 784kN, gap depth 400mm, open height 420mm, SN: 80200099, CS ...
Tokigawa, Japan
1999 AMADA [60t universal hydraulic bender] SPH-60C
- Manufacturer: Amada
- Model: SPH-60C
Product name: Hydraulic bender | Main specifications: Pressure capacity 60t Stroke length 150mm Table length 1000mm Gap depth 510mm Max. descent speed of slide 50mm/s Tank capacity 87(l)
Tokigawa, Japan
1993 Amada CSW-250
- Manufacturer: Amada
- Model: CSW-250
- Maximum thickness: 6 mm
- Shearing length: 2,500 mm
Product name: Shearing | Main specifications: OH240010 Compression capacity 10 tons・ Maximum processing size Corner notch 250x250 mm・ Edge notch maximum 100x150 (standard 50x150) Maximum processing板 thickness 3...
Tokigawa, Japan
1999 AMADA [Vendor] FBD1253NT
- Manufacturer: Amada
- Model: FBD-1253NT
- Stroke length: 150 mm
- Throat depth: 320 mm
Product name: Other cutting machines | Main specifications: Pressure capacity 125TON, stroke length 150mm, table length 3000mm, gap depth 400mm, max. lift speed 77/90(50/60Hz), power supply 200/220V 3 phase 50/6...
Tokigawa, Japan
Max WH-2
- Manufacturer: Max.
Rose nails for siding. Plastic sheet can be easily connected.
$650 USD
Kumagaya, Japan
Makita AN936H to AN936HM
- Manufacturer: Makita
Powerful Low recoil Low noise. Air pressure: 1.28 to 2.26 sMpa | Nails used: Wire nails 45-90mm Sheet nails (wide) 45-75mm | Number of nails loaded: Wire nails: 120-300 (1 roll)Sheet nails: 200 (1 roll) | Mass: 2...
$651 USD
Kumagaya, Japan
1984 Amada RG-50S
- Manufacturer: Amada
- Model: RG-50S
- Stroke length: 120 mm
- Throat depth: 320 mm
Product name: Hydraulic bender | Main specifications: Pressure capacity: 50 t stroke: 100 Table length: 1200 Gap depth: 400 Open height: 370 Auto back gauge 2010 without clamper
Tokigawa, Japan
1987 Amada CS-220 Corner Shear
- Manufacturer: Amada
- Model: CS-220
- Maximum thickness: 6 mm
- Shearing length: 2,200 mm
Capacity: 10t Stroke length: 25 Corner notch: 220 x 220 Edge notch: 50 (width) x 100 (depth) Instructions, specifications, drawings None
Tokigawa, Japan
Makita KS001GRDX
- Manufacturer: Makita
Rotational speed 7,500 min-1 (in speed mode). Achieves cutting speed approximately 10% faster than our AC model Battery BL4025 x 2, charger DC40RA, case, Allen wrench 5, parallel ruler *Chip saw is not included.
$569 USD
Kumagaya, Japan

12

Overview

Machine tools are devices used in manufacturing to shape or machine metal and other rigid materials, typically by cutting, boring, grinding, shearing, or other forms of deformation. They are essential in producing precise and complex parts in industries such as automotive, aerospace, and electronics, and include a variety of machines like lathes, milling machines, and CNC machines.

FAQ

What should I consider when buying a used machine tool?

Evaluate the machine's condition, age, and maintenance history. Check for any signs of wear or damage and ensure it meets your specific production requirements.

How do I ensure the machine tool is shipped safely to my location?

Hire a transport service experienced in moving heavy machinery. Ensure the machine is properly secured and protected to prevent damage during transit.

What is the maintenance schedule for machine tools?

Regular maintenance includes lubricating moving parts, inspecting for wear and tear, and calibrating for accuracy. Follow the manufacturer's guidelines for specific maintenance tasks and intervals.