- Trusted Seller
KME SCHMOLE WT-LOK 8-01.23-2 SHELL & TUBE HEAT EXCHANGER OIL COOLER ARBURG 320K
used
- Manufacturer: Arburg
KME SCHMOLE WT-LOK 8-01.23-2 SHELL & TUBE HEAT EXCHANGER OIL COOLER PULLED FROM AN ARBURG 320K PLASTIC INJECTION MACHINE. INV# P-501
$750 USDHenderson, KY - Trusted Seller
NEW THERMAL TRANSFER Heat Exchanger A-1024-2-6-F Four Pass 5" x 24"
new
- Manufacturer: THERMAL TRANSFER
🔥 NEW THERMAL TRANSFER Heat Exchanger A-1024-2-6-F Four Pass 5" x 24" INV# P-969
$1,500 USDHenderson, KY - Trusted Seller
NEW THERMAL TRANSFER Heat Exchanger C-1024-5-6-F Four Pass 5" Baffles 1.5 NPT
new
- Manufacturer: THERMAL TRANSFER
🔥 NEW THERMAL TRANSFER Heat Exchanger C-1024-5-6-F Four Pass 5" Baffles 1.5 NPT INV# P-968
$1,500 USDHenderson, KY - Trusted Seller
Arburg Injection Molding hydraulic Pressure Gauge
used
- Manufacturer: Arburg
Arburg Injection Molding Hydraulic Pressure Gauge 6 Position Item is used. INV # P-70 Powered by eBay Turbo Lister The free listing tool. List your items fast and easy and manage your active items.
$200 USDHenderson, KY - Trusted Seller
MITSUBISHI Plastic Injection Molding Machine Barrel Zone Heating Control Power
used
- Manufacturer: Mitsubishi
“Pulled from working Mitsubishi Molding Machine” MITSUBISHI Plastic Injection Molding Machine Barrel Zone Heating Control Power Supply Board INV# P-1327
$200 USDHenderson, KY - Trusted Seller
Conair 10721301 Dryer Input/Output Board - Free Shipping
used
- Manufacturer: Conair
🔥Conair 10721301 Dryer Input/Output Board - Free Shipping INV# P-1517
$350 USDHenderson, KY - Trusted Seller
(NEW) VAN DORN Barrel End Cap 350 Ton Plastic Injection Molding Machine
new
- Manufacturer: Van Dorn Demag
🔥 (NEW) VAN DORN Barrel End Cap 350 Ton Plastic Injection Molding Machine 15 Holes. Female Thread for the Nozzle is about 60mm. About 5-5/8" Diameter NOTE: We think this is for a 350 Ton Press. Ask all questions ...
$500 USDHenderson, KY - Trusted Seller
6" Diameter Taisel Kogyo Industrial Heat Exchanger Model FCF-216-2 R-2323
used
- Manufacturer: American
“Pulled from machine with low hours” Taisel Kogyo Industrial Heat Exchanger Model FCF-216-2 R-2323 About 12" Long by 6" in Diameter ITM# P-177
$500 USDHenderson, KY - Trusted Seller
(TESTED) MITSUBISHI PLCS-10 OPERATOR PANEL INJECTION MOLDING MACHINE
used
- Manufacturer: Mitsubishi
“Pulled from working machine” 🔥(TESTED) MITSUBISHI PLCS-10 OPERATOR PANEL INJECTION MOLDING MACHINE INV# P-1302
$1,000 USDHenderson, KY 
PENDU Live Rolls with measuring stops
used
- Manufacturer: Pendu
Live rolls with 3 pop-up stops 24" apart, no drive. Slots for pop-up transfer chains. Rolls are 6-1/2" diameter and approximately 13-1/2" wide. Overall length approximately 20'.
Oneida, KY
G-Tek Flat Belt 15' x 21"
used
- Manufacturer: G-Tek
Flat table top style product conveyor. Factory built with hydraulic motor drive. 21" wide belt approximately 15 feet long.
Oneida, KY
Louisville, KY
GRIEVE BF-122412-HT, BT-122012
used
- Manufacturer: Grieve
GRIEVE OVER/UNDER FURNACE MODEL BF-122412-HT w/TEMPERING FURNACE MODEL BT-122012 460V 3 Phase 26 Amps 20 KW 26 Amps -Workspace Dimensions: upper - 12" wide x 24" deep x 12" high; lower - 12" wide x 20" deep x 12"...
- Trusted Seller
2017 KAESER EB421C
used
- Manufacturer: Kaeser
This blower has never been used, purchased for a project and the job was cancelled.
Louisville, KY - Trusted Seller
DONALDSON VF-150
used
- Manufacturer: Donaldson / Torit / DCE
Aircel VF-150, 150 CFM, 115V, NEMA 4 Non-Cycling Refrigerated Air Dryer 150 CFM capacity 200 PSIG max operating pressure 100°F inlet temperature 38°F dew point Timer drain Internal high-efficiency separator R-134...
Louisville, KY
Tip: Enter manufacturer, model or keyword
