Used Materials Testing in Taiwan

Portable Pencil Hardness Tester Confirm to ASTM D3363, ECCA T4, MILC27 227, NEW5350, SIS184187, SNV37113, JIS-C3003/D0202 Standard
- used
GI-M010 according to WolffWilborn standard, this tester is designed to measure the coating surface hardness scrape-resistance, applied to experiment analysis or control production quality, suitable products inclu...
Taichung City, Taiwan
Circular Sample Cutter Confirm to ISO3801, ASTM D3776, GB/T4669, BS2471 Standard
- used
- Manufacturer: cometech testing machines
QC-PS can cut specimens of area 100cm², weighing specimen unit weight, the balance of the required minimum reading value should reach 0.01 g. The cutter can cut specimens that thickness are 5 mm. Cutting material...
Taichung City, Taiwan
QC-622H Surface Hardness Abrasion Tester
- used
Surface Hardness Abrasion Tester is for measuring surface treatment such as painting, plating, coating, dyeing and finishing the design of the machine. It can use cotton, sand paper, steel wool and eraser to test...
Taichung City, Taiwan
QC-113A Pneumatic Type Drop Tester Confirm to ASTM 5276 / GB/T 4857.5 / CNS 2999 / ISTA 1A / ISTA 2A Standard
- used
- Manufacturer: cometech testing machines
Suitable for testing the impact resistance of packaging and electronic products during transportation. It features a single-wing structure, occupies a small space, and is typically used to simulate product impact...
Taichung City, Taiwan
Spray Tester Confirm to JIS- L1092 , BS EN 24920 , AATCC-22 , ISO 4920, ASTM D1913-2000, ASTM D583-54 Standard
- used
- Manufacturer: cometech testing machines
QC-305 may test water-proof or non-water-proof textile surface water resistance. Clamping textile with 45 degree angle on grip, hold open around 150mm diameter plane, putting sprayer above sample center 150mm, sp...
Taichung City, Taiwan
Portable Hydrostatic Head Tester
- used
- Manufacturer: cometech testing machines
QC-317M(N) Portable design and without electricity that can proceed with test. No time and space limitations, mainly used on the spot measurement, inspect textile water-resistance ability. The test method is divi...
Taichung City, Taiwan
DIN Abrasion Tester Confirm to DIN53516 ISO-4649 GB/T 9867 SATRA TM174 Standard
- used
QC-618A is suitable for elastic material, rubber, tires, conveyor belts, transmission belts, shoe soles and software synthetic leather. The specimen of wear area is dia. 16mm which provide the required load and t...
Taichung City, Taiwan
Tape Holding Power Tester (Normal Type) 10 sets Confirm to GB/T 4851, ASTM D3654, PSTC 7 Standard
- used
- Manufacturer: cometech testing machines
QC-801(A)(B)(C) Specimen stick test area can use 1/2”x1”or 1”x1”, unified to use 0.45 pound of load scrunch through specimen, hanging counterweight in the lower end of specimen. Timer automatically stops counting...
Taichung City, Taiwan
Coefficient of Friction Tester, Motor Coefficient of Friction Tester Confirm to TAPPI T-815, ASTM D202 Standard
- used
- Manufacturer: cometech testing machines
QC-117 & QC-117A Put specimen on the platform, and then put dead weight on the top of specimen according to standard requirement. Let platform angle goes up until the deadweight slides down. Get the tan value fro...
Taichung City, Taiwan
Manual Roller , Motor Roller Confirm to JIS-C2107, Z0237, PSTC 7 Standard
- used
- Manufacturer: cometech testing machines
QC-803A QC-803A is controlled by hand, hold roller and slightly go up, let fixed base leave the axle center, this moment the roller equals to standard weight, with 300mm/min speed back and forth roll through spec...
Taichung City, Taiwan
Perspiration Tester Confirm to AATCC-15, ISO 105, JIS 0848, GB T5713 Standard
- used
- Manufacturer: cometech testing machines
QC-315 is used to determine the fastness of colored textiles soaked in water condition. Using textile and one piece (multi-fiber fabric) or two pieces (single fabric) stitched, after soaking in solution, be clamp...
Taichung City, Taiwan
GR-L020 Narrow Grip
- used
- Manufacturer: cometech testing machines
Capacity: 10N | Jaw face width: 20mm | Specimen thickness: 0.1~9mm | Mini. load cell: 10N | Temperature limits: 0~100℃ | Weight: 123g
Taichung City, Taiwan
GR-L010 Elasticity Grip
- used
- Manufacturer: cometech testing machines
Capacity: 10N | Jaw face width: 9mm | Specimen thickness: 0.1~2mm | Mini. load cell: 10N | Temperature limits: 0~100℃ | Weight: 38g
Taichung City, Taiwan
GR-L030 Button Grip
- used
- Manufacturer: cometech testing machines
Capacity: 300N | Wire diameter: Ø7~Ø15mm | Mini. load cell: 200N | Temperature limits: 0~200℃ | Up weight: 925g | Down weight: 3468g
Taichung City, Taiwan
GR-I020 Adjusted Grip
- used
- Manufacturer: cometech testing machines
Capacity: 500N | Jaw face width: 88mm | Specimen thickness: 80mm | Temperature limits: 0~100℃ | Weight: 2256g
Taichung City, Taiwan