Used Material Handling in Michigan, USA

40' high cube 8’ wide x 8’6” tall swing doors on one end wood deck rings for tie downs inside

40' high cube 8’ wide x 8’6” tall, swing doors on one end, wood deck, rings for tie downs inside, scattered dings/dents, decking showing wear in a couple spots, weighs approx. 8,160 lbs, used

BUNTING 33373 Drawer Magnet USED

• Manufacturer: Bunting

1 7/8" Diameter Inlet / Outlet Hole Top of Flange 6.25" x 6.25" Top Flange 1.25" Cone 1.25" Cylinder 3.75" x 6" Bottom Flange 1 7/8" Diameter Bottom Inlet / Outlet 2.25" from Top of Cone to Cylinder 5" x 5...

1989 Novatec NPH-HOPPER Used

• Manufacturer: Novatec
• Model: NPH-

600 lb Capacity Buyers are welcome to inspect equipment prior to purchase. Expedited shipping services are available upon request. This piece is located at Ideal Machinery, Inc. on our showroom floor. Located...

CONAIR FRANKLIN DB12SE03MB DustBeater Vacuum Loader USED

• Manufacturer: Conair

4" Cylinder Height 7.25" Cone Height 12" Inside Cylinder 13.75" Filter Diameter 14.5" Inside Lid Cylinder 4.75" Bottom Inlet / Outlet Approx. 40.79 mm Tested Good Buyers are welcome to inspect equipment p...

UNA-DYN LS-45 Auto Loader USED

• Manufacturer: Una-Dyn

Self Contained with Lid and Filter Outside Diameter: 10" Inside Diameter: 9" Outlet 1 Inside Diameter: 1.25" Bottom Outlet Inside Diameter: 3" Flange: 7" x 5.5" Holes Center-to-Center: 6.5" x 5" 110 Volt ...

UNA-DYN 82894.06 Loader Used

• Manufacturer: Una-Dyn

82894.06 LID AND FILTER INCLUDED OD: 10" ID: 8 3/4" Outlet 1: 1 1/2" Bottom outlet: 2 1/2" Flange: 7" x 5 1/2" Bolt Holes, Center-to-Center: 6 1/4" x 4 3/4" Buyers are welcome to inspect equipment prior t...

CONAIR DB8 DustBeater Vacuum Loader USED

• Manufacturer: Conair
• Model: DB8

Self-Contained 200 lbs/hr Recommended Throughput 8" Loader Diameter 0.14 Cu Ft Loader Volume 80 PSI Compressed Air Requirement 50' Max Conveying Distance 1,5", 1.75", 2" Material/Vacuum Line Size Available ...

MAGUIRE MLS-580 Clear Vu Loading System Used

• Manufacturer: Maguire
• Model: MLS-580

120 Volt 1 Amp Tested Good Expedited shipping services are available upon request. All taxes due are the responsibility of purchaser. Visitors are welcome to inspect equipment prior to purchase. This piece ...

AEC WHITLOCK Vacuum Loader SLC04 USED

• Manufacturer: AEC

115 Volt Single Phase 60 Hz Motor: 1.5 HP, 11 Amp 115 Volt Control Circuit Tested Good Buyers are welcome to inspect equipment prior to purchase. Expedited shipping services are available upon request. Th...

BUNTING MAGNETICS 81937 Drawer Magnet USED

• Manufacturer: Bunting

56.75 mm Diameter Inlet / Outlet Top Flange Approx. 7" x 7" Top Flange 50.67 mm Diameter Inlet / Outlet Bottom Flange Approx. 1.25" Cone Height 1.25" Cylinder Height Expedited shipping services are available...

EMI METAL FABRICATING Drawer Magnet USED

• Manufacturer: EMI

50.58 mm Diameter Inlet / Outlet Top Flange Approx. 7" x 7" Top Flange 7" x 7" Bottom Flange 5.5" x 5.5" Center to Center Holes Bottom Flange Approx. 69.71 mm Diameter Inlet / Outlet Bottom Flange Approx. Ex...

PPE Drawer Magnet USED

• Manufacturer: PPE

2" x 2" Inlet / Outlet Top 4.5" x 4.5" Top Flange 3" Bottom Cone Height 4.5" x 4.5" Bottom Flange 3" x 3.5" Center to Center Holes Bottom Flange 2" x 2" Bottom Inlet / Outlet Expedited shipping services are...

METAL FABRICATOR Drawer Magnet USED

• Manufacturer: METAL FABRICATOR

49.80 mm Diameter Top Flange Inlet / Outlet 6" x 6" Top Flange 5" x 5" Center to Center Holes Top Flange 7.5" Cylinder Height 1.25" Cone Height 1.25" Bottom Cylinder Height Expedited shipping services are a...

METAL FABRICATOR Drawer Magnet USED

• Manufacturer: METAL FABRICATOR

6.5" x 6.5" Top Flange 3" Diameter Inlet / Outlet Top Flange Approx. 3.25" Cone Height 6.5" x 6.5" Bottom Flange 5.5" x 5.25" Center to Center Holes Bottom Flange Approx. 3" Diameter Inlet / Outlet Bottom Fl...

METAL FABRICATOR Drawer Magnet USED

• Manufacturer: METAL FABRICATOR

7" x 7.25" Top Flange 76.71 mm Diameter Top Inlet / Outlet 2" Cone Height 1" Cylinder Height 7" x 7" Bottom Flange 5" x 5.75" Center to Center Holes Bottom Flange 51.75 mm Diameter Inlet / Outlet Bottom Fla...