Used controllers

2006 JERN YAO JNFP 14B5S

• Manufacturer: JERN YAO

Max. cut-off dia.: 14 millimeters | Max. cut-off length: 13 millimeters | Maximum kickout: 15mm | Maximum pko stroke: 8mm | Maximum production: 280 PPM | Electrics: 30 HP ACVD Motor and Controls | Approx. weigh...

2,500 ton Lake Erie 4-Column Down-Acting Closed Die Oil Hydraulic Forging Press Re:24874

• Manufacturer: Erie Press Systems

Still installed and under power Force: 2,268 tonnes | Hyds: Oil | Stroke: 1,600 mm | Daylight: 3,505 mm | Bed l-r: 38,100 mm | Bed f-b: 33,020 mm | Press action: Push Down | Number of columns: Four | Number of ma...

1979 National 1000 Ton Maxi Pres

Imperial Metric National 1000 Ton Maxi Pres Cieco PLS Plus Control PWI Tonnage Monitor Dual Palm Buttons Foot Pedal Top and Bottom Knock Outs

30,000 ton 8-Column All Steel Push Down Type Hydraulic Closed Die Forging Press – Re:24444

• Manufacturer: East European Built

Complete with: Number of movable tables – (2) Number of side ejectors – (2) Moving table under the press front to back Documentation sufficent to maintain the press in production including parts drawings Note : W...

1991 WILLIAMS-WHITE 2000 TON HYDRAULIC VERTICAL PRESS

• Manufacturer: Williams - White

• COMPLETE UNIT • 2000 TON HYDRAULIC VERTICAL PRESS (72 INCH STROKE LENGTH, 146 INCHES PER MINUTE PRESS SPEED) • HYDRAULICS WITH OIL COOLER • ELECTRICAL • PLCS AND CONTROL SYSTEM (SHARED CONTROL PANEL WILL REQUIR...

CLEVELAND 10K

• Manufacturer: Cleveland
• Model: 10K

Equipped With * Dual palm button controls * Air Clutch Shut Height With 6? Plate On Ram: 25"

Duisburg 7,500 Ton Forging Press

• Manufacturer: Duisburg

Repair of Overall Geometry: Replacement of Column 4 Re-Machining of Columns 1-3 Machining & Pre-Stressing of the Heap Table & Replacement of Slide Rails Replacement of Mobile Gantry Guide Rings Repair of the Pre...

1960 1,500 Ton Clearing Oil Hydraulic 4-Column Push-Up Type Open/Closed Die Forging Press – Re:23304

• Manufacturer: Clearing

This press is equipped with the following: (2) Pullbacks – 6” dia x 3” dia rod – 20 tons (2) Nordberg 6000 PSI Valve Unit Pumps ( 2) Siemens-Allis 250 HP induction motors (54.2 Amps 1780 RPM 2400 Volts) (2) Nordb...

1951 5,000 ton Lake Erie Push Down type

• Manufacturer: Erie Press Systems

Additional info: Equipped With: Rubber Pad Fluid Forming Unit Top Mounted Hydraulic Power Unit Including: (1) 60 HP Oilgear Hydraulic Pump #DX-6011 - 880 RPM - 1100 Rated Pressure (1) 150 HP Oilgear Hydraulic Pum...

1953 7,000 ton Hydraulic Push Down

• Manufacturer: HPM

Additional info: 65 Ton Total Die Lifting And Stripping Capacity @ 1500 PSI 36” Floor To Top Of Bolster 238 IPM Fast Advance Speed 17.5 IPM Pressing Speed 238 IPM Return Speed 630 – 6,300 Ton Infinitely Variable ...

Press Transfer Forging AIDA

• Manufacturer: Aida

FOUR POINT CRANK MOTION STRAIGHT SIDE SERVO TRANSFER PRESS Capacity : 1635 tons, Stroke : 600 mm, Stroke per minutes : 24, Bed size : 6000 x 2410 mm, Die Height (SDAU Bolster) : 1200 mm, Adjustment : 295 mm...

1000 tons Press Hot Forging Erie MFP

• Manufacturer: Erie

Capacity : 1000 tons, Stroke : 250 mm, Stroke per minutes : 90 spm, Shut height : 600 mm, Bed size : 750 x 1000 mm, Ram size : 750 x 775 mm, Dual palm buttons : Yes, Calico automator control : Yes, Scotch...