- Trusted Seller
1971 PLATARG 611
- Manufacturer: PLATARG
Platarg transfer press 611 Specifications: Number of stations: 12 (11+1) Capacity per ram: 6 tons Maximum stroke: 114 mm Max. shell height: 50 mm Standard ram pitch: 82 mm Blank diameter: 80 mm
Niederhelfenschwil, Switzerland - Trusted Seller
1987 PLATARG 912
- Manufacturer: PLATARG
The press is now in storage - was in a full running state when taken out of service. High lift stroke cams 159 mm - max. shell height 76 mm 13 Stations, 12 Rams + 1 Slave Wedge Adjustable Rams with Standard Male ...
Niederhelfenschwil, Switzerland - Trusted Seller
1997 BMV T1/250/22-11/150-300/380
- Manufacturer: BMV
Object: 48337 | Drive system: eccentric / crank | Number of suspensions: 2 | Number of slide actions: 1 | Slide ejectors / cushion: yes | Table cushion: yes | Feedstock transport direction: left to right | Total...
Niederhelfenschwil, Switzerland - Trusted Seller
1996 PLATARG 2513
- Manufacturer: PLATARG
Can be tested in operation Max. Flywheel speed: 760 1/min. Capacity on one stage approx. 25T Clutch engagement max. 10/min Air pressure 5.5 bar (min) - 5.8 bar (max) Total deceleration time Braking <250 ms Zig...
Niederhelfenschwil, Switzerland - Trusted Seller
1977 PLATARG 611
- Manufacturer: PLATARG
A new electrical control system and a mechanical and lubrication rebuild are required. One used PLATARG model 611 transfer press, high speed type. Full follow cams. Number of stations: 12 Number of rams: 11 + 1 s...
Niederhelfenschwil, Switzerland - Trusted Seller
1969 PLATARG 312
- Manufacturer: PLATARG
This machine can have the following installed/added to it (not included) o new lubrication o new electrical installation o new protections o CE conformity Number of station 13 (12+1). Capacity on any one station ...
Niederhelfenschwil, Switzerland - Trusted Seller
2000 BENELLI 650T/3MR/2/12/3750X1100/LD/ET3
- Manufacturer: Benelli
Press equipped with 2 feeing lines - one from the side for blank cutting in transfer mode and one in line for for progressive die operation.
Niederhelfenschwil, Switzerland - Trusted Seller
1999 KOHLER 50.140/21-3000.1VSRM + HK
- Manufacturer: Kohler
KOHLER coil line consisting of: - Coil loading chair CS3000 - Decoiler 300.1 H - VSRM 50.140/21 leveller - HK 140 upright leveller
Niederhelfenschwil, Switzerland - Trusted Seller
2005 ARKU RM 50X/9 ECOPLAN
- Manufacturer: Arku
Cut-To-Length line consisting of: - Coil loading chair HUBTEX - ARKU single-sided decoiler - ARKU VRM 5050/9 feed straightening machine, +- 0.1 mm feeding precision - measuring wheel to verify feed length - Cut-t...
Niederhelfenschwil, Switzerland - Trusted Seller
SCHULER PDR 250-500
- Manufacturer: Schuler
- Model: PDR 250-500
Object: 43587 | Last overhaul: 2002 | Drive system: eccentric / crank | Frame design: C-frame, single sided | Opening in table: yes | Total force (nominal): 250 to | Table surface (left-right): 800 mm | Table ...
Niederhelfenschwil, Switzerland - Trusted Seller
1980 BETZ EZL 300
- Manufacturer: BETZ
approved for single stroke Safety valve make Herion Pneumatic clutch make Desch Motor grease - central lubrication ram weight - compensation cylinder Motorized height adjustment T-slots in the ram Freestanding co...
Niederhelfenschwil, Switzerland - Trusted Seller
Niederhelfenschwil, Switzerland - Trusted Seller
1996 IMS 80 RE
- Manufacturer: IMS
Object: 53951 | Drive system: eccentric / crank | Total force (nominal): 80 to | Table surface (left-right): 560 mm | Table surface (front-back): 376 mm | Spigot hole diameter: 50 mm | Stroke: 110 mm | Stro...
Niederhelfenschwil, Switzerland - Trusted Seller
Niederhelfenschwil, Switzerland - Trusted Seller
2020 ZANI SM90 K1 -09-50
- Manufacturer: ZANI
Object: 42740 | Drive system: servomechanic | Openings in uprights: yes | Number of slide actions: 1 | Table cushion: yes | Total force (nominal): 90 to | Table surface (left-right): 900 mm | Stroke: 500 mm |...
Niederhelfenschwil, Switzerland
Tip: Enter manufacturer, model or keyword