Used Extruders

MATSUII DMZ-120

• Manufacturer: MATSUII

Used Matsui dehumidifying dryer. Model DMZ-120, Serial #01464, new 1995. Rated at 120 CFM. Has 3 KW heater, 230 volt, 3 phase, 60 hertz. Includes hopper mounted on a portable stand.

RANDCASTLE Ø51 мм × 203 мм

• Manufacturer: RANDCASTLE

Used 2" O.D. x 8" Wide Randcastle Sheet Extrusion 3-Roll Stack including Pull Roll Station and Single Position Winder.

BUSS 200 HP

• Manufacturer: Buss

Used 100mm Buss kneader with 9/1 L/D barrel. Driven by 200 hp DC motor, includes 5.94/1 gearbox, jacketed barrel and clam shell barrel opening. Includes operator control panel. Kneader will discharge into approxi...

1994 1994 Berstorff 125 HP 6 Meter x180MM Twin Screw Extruder Reactor

1994 Berstorff N/A 125 HP 6 Meter x 180mm Twin Screw Extruder Reactor Consists of: 30,000 Flender process speed reducer Screws Barrel Die Outlet flange 2 heating zones 2 cooling zones 4 circulation pumps Shaft eq...

RANDCASTLE Ø19 мм, L/D 24:1

• Manufacturer: RANDCASTLE

Used Randcastle Laboratory Sheet Extrusion Line Consiting of the Following Items: - .75" Randcastle 24/1 L/D extruder with temperature control panel, model RCP0750, serial #J2271. - 2" O.D. x 8" wide chill roll s...

2003 WERNER & PFLEIDERER ZSK20

• Manufacturer: WP
• Model: ZSK20

Used 20mm Werner & Pfleiderer model ZSK20 co-rotating twin screw extruder. Has 40/1 L/D barrel at 43" centerline height driven through a 3:1 gearbox with a 37-Newton meter torque capacity per screw shaft. Extrude...

Conair D400H

• Manufacturer: Conair
• Model: D400H

Used Conair model D400H high heat desiccant dryer, 300 cfm. Have carousel desiccant cartridges, operator controls, no hopper. Previously used with 900-1000 lb hopper.

THORESON MCCOSH TD2000

• Manufacturer: Thoreson McCosh

Used 6,000 lb. Thoreson McCosh Desiccant Dryer Model TD2000. Serial #201-703-05. 480 volt, AC input, 20 hp. Amps 236.0, kw 182.0. No hopper included.

UNA-DYN GS150

• Manufacturer: Una-Dyn

Used Una Dyn Piovan Desiccant Dryer. Model GS150, serial #237240-01-01-0903. Rated at 150 cfm. Includes approximately 800 LB., 30" diameter x 72" straight side x 19" cone bottom insulated hopper with top mounted ...

2008 COPERION ZSK-40-MEGA

• Manufacturer: Coperion Waeschle

Used 40mm Coperion Mega 40 co-rotating twin screw extruder. New 2008. No barrels or screws included. Driven by 200 hp AC motor, 1790 rpm, with Powerflight VFD controller. Has 1.155 gear ratio supplying 1200 rpm s...

BRABENDER 88

• Manufacturer: Brabender

Used 25mm 24/1 L/D Brabender twin screw extruder package. Has air cooled extruder, temperature control panel, type D10002, prep center with model 088 type 09-25-000 temperature pressure module. Includes 10 HP DC ...

BATTENFELD CINCINNATI CM55

• Manufacturer: Battenfeld-Cincinnati

Used Battenfeld-Cincinnati model CM55 counter rotating approximately 55mm diameter twin screw extruder. Conical screw design. Barrel is electrically heated and air cooled in three zones with air blowers with 0.20...

Cincinnati CMT80L-APC

• Manufacturer: Cincinnati
• Model: CMT

Used Cincinnati model CMT80L-APC conical counter rotating twin screw plastic extruder. Screw length approximately 1,665mm long x 80mm diameter at the discharge. Has adaptor plate that reduces the barrel exit down...

ZUMBACH KW20

• Manufacturer: Zumbach
• Model: KW20

Used Zumbach model KW20 surface fault detector.