Used Mineral Processing

Wemco No. 144 Flotation Mechanisms

• Manufacturer: Wemco

30 HP Motor 890 RPM 460 Volts Includes: Rotors Dispersers Disperser Hood (Skirts) Draft Tubes & Collars 4 Units Available

Gray Bros. Style Wash Plant

Gray Bros. Style Wash plant Rebuilt and Upgraded in 2015 Diesel/hydraulic Drive: 8ft x 10ft Lined Dump Box 5ft x 12ft Shaker Box 4ft x 8ft Sluices On Each Side Single hutch water pulse jig built in. 6in Water Int...

Wemco #84 Flotation Unit Cell

• Manufacturer: Wemco

Feed and Discharge Boxes Launder Trough on One Side Completed with: 15 HP Motor and V-Belt Drive 575 Volts 1180 Rpm

Wemco No. 84 Flotation Cells

• Manufacturer: Wemco

1 Bank of 2 Cells 2 General Electric Single Drive Motors 15 HP 440 Volt 1775 RPM Double Overflow 2 Units Available

Wemco No. 44 Single Overflow Flotation Cells

• Manufacturer: Wemco

6 Banks of 2 Cells Single Overflow Tank (2) 5 HP Motor 1760 RPM 460 Volts 1 for each Mechanism Floth Paddle Shaft Driven by a Right Angle Boston Gearhead Motor 1/4 HP 230/460 Volts 1725 RPM 50-1 Ratio Feed Box (2...

Wemco-Style Flotation Cell Parts Kits

• Manufacturer: Wemco

Replacement wear and critical spare parts for Wemco-style flotation cells - Parts fit Wemco original cells and D'Angelo Wemco-style cells - Refer to table below for models available - Wear material is vulcanized ...

Denver-Style DR Flotation Cell Parts Kits

New manufacture parts kits for Denver-Style DR flotation cells - Parts are interchangeable with original Denver DR cells or D'Angelo's DR-style cells - Standard wear part material is 520 natural black rubber - Ru...

Sub-A Denver-Style Flotation Cell Parts Kits

Wear and spare parts kits for Denver-style Sub-A flotation cells - Parts fit original Denver Sub-A cells as well as D'Angelo Sub-A flotation cells - Wear parts use hot vulcanized 520 black rubber - Parts diagram ...

Denver DR 24 Impellor and Diffuser Rubber Parts

- Lot of 10 Units: Denver DR 24 Impellers and Diffusers - Impellers: Natural rubber, bolt on type, 9 vane - Diffusers:  Natural rubber, 16 fins, 6” deep - Year of manufacture: 2013 - Condition: Unused surplus

Hydraulic Grinding Mill Inching Drive

Hydraulic Grinding Mill Inching Drive Mechanically connects to the non-drive end of the primary pinion A flanged hub on the output shaft of the reduction unit slides over to bolt to the existing hub on the pinion...

30 x 7 ft (9.1 x 2.1 m) Allis Chalmers ( Metso) SAG Mill components with 4079 HP motor, 200 RPM

• Manufacturer: Allis-Chalmers

Allis Chalmers 30 x 7 ft SAG - Westinghouse AC brushless synchronous motor with spare stator: - 4079 HP (3000 kW) - 200 RPM - 3300 V - 50 Hz Mill includes: - Bull gear - Pinions - Lube units - Slide shoe bearings...

Steel grinding balls

- Used steel grinding balls - 3 inch minus, majority are 1.5-2.5 inches - Cleaned and stored in barrels - Ready for shipment - Large quantity available

Eaton 38 VC 1200 Air clutch

• Manufacturer: Eaton

Complete new and unused Eaton airflex clutch 1- 38VC1200 Element ASSY 2 SC 1- I.O.M Manual 1 1 - 38VC1200 Drive hub 1 - 38VC1200 Male reg drum 2 - Hose assembly 1 - 38VC1200 Spider Inquire about other Eaton clutc...

Mill, Sag, 38' X 25'5", Metso, 26,000 HP, Unused #D739652

• Manufacturer: Metso

Unused Metso grate discharge sag mill trommel with replacement panels, 38' (11.58 m) diameter x 25' 5" (7.76 m) long, 26,000 HP (19,400 kw) Siemens wrap around drive motor-operating frequency 60 Hz. EGL: 22' (6.7...

METSO OUTOTEC e200

• Manufacturer: Metso

Tank Size: LOT of 6 UNUSED METSO OUTOTEC Forced Air TankCell e200 Flotation Cells