Used controller

Trusted Seller
1988 Welex 41''
- Manufacturer: Welex
Used Welex 41" sheet extrusion line:- 3.5" 30/1/ L/D Welex extruder. Has vented and plugged barrel, but includes 2 stage screw and spare screw. Has electrically heated water cooled system with water pump. Extrude...
Valley Cottage, NY
GLOUCESTER 2.5″ 32:1 L/D EXTRUDER 17690
Gloucester 2.5″ extruder, 32:1 L/D five (5) zone air cooled and vented barrel at a 45″ centerline height. Top center feed throat. Driven by a 50 HP A/C 1750/2100 RPM motor, includes 6 zone temperature control pan...
Elk Grove Village, IL
AET 10/6″ Dual Diamter Extruder
AET dual diameter 10″-6″ – 32:1 L/D 50” centerline height film reclaim extruder with Koellmann gear double reduction gear reducer, with oil pump, heat exchanger cooling system, cast water cooled feed throat with...
Rockville Centre, NY
Trusted Seller
1977 FIELDING & PLATT 1600mton Aluminum Extrusion Line
- Manufacturer: FIELDING & PLATT
Manufacture: - Fielding & Platt - New 1977 - Decommissioned 2013 in good running condition Scope - Press - complete and proper, installed and included - Press control cabinets installed and included - Billet hea...
Banner Elk, NC
Trusted Seller
DAVIS STANDARD 1.5"
- Manufacturer: Davis-Standard
- Model: 15
Used 1.5" Davis Standard 28/1 L/D Non-Vented Air Cooled Extruder. New in 1989. Equipped with 6.53/1 gearbox ratio. Gearbox is belt driven through a 15 hp DC motor. Includes temperature control panel with motor dr...
Hainesport, NJ
CINCINNATI MILICRON (WELEX) 2 ROLL 6547
- Manufacturer: Cincinnati
Cincinatti Milicron 2 roll stack / laminator, no S/N. Two (2) chrome rolls 17.75″ diameter 34″ wide cored for cooling. Two (2) aluminum guide rolls. One (1) is 17.75″ diameter x 31″ wide, and one (1) is 8″ diamet...
Elk Grove Village, IL
Trusted Seller
CONAIR D901601
- Manufacturer: Conair
Conair Franklin Electric/Gas Dryer model D901601, 480V, with Compu-Dry computerized drive control, 15HP motor, with Alzeta Corp Pyrocore Burner model PCA 250S, 250 BTU natural gas
Valley Cottage, NY
Power Curbers 150 Extruder
- Manufacturer: Power Curbers
Power Curbers pioneered the extruded curb concept in the early 1950s and has been building extruders for over 65 years. For jobs that require less expensive scab-on curb, the 150 extruder is ideal. The mix is fed...
Salisbury, NC
Trusted Seller
CONAIR D901601
- Manufacturer: Conair
Conair Franklin Electric/Gas Dryer model D901601, 480V, with Compu-Dry computerized drive control, 15HP motor, with Alzeta Corp Pyrocore Burner model PCA 250S, 250 BTU natural gas
Valley Cottage, NY
Trusted Seller
6" Davis Standard Egan / Berringer Water Ring Pelletizing Line
- Manufacturer: Davis-Standard
6" Davis Standard Egan / Berringer Water Ring Pelletizing Line Used 6" Davis standard Egan / Berringer water ring pelletizing line consisting of: 6" Davis Standard Egan extruder, model 6026-D.R.H, 44:1 l/d, elect...
Cleveland, OH
DAVIS STANDARD 165MM60TPIH 6.5″ EXTRUDER 10869
- Manufacturer: Davis-Standard
Davis Standard model 165MM60TPIH, S/N X7206 27:1 L/D 150HP DC motor 100RPM screw speed 526HP rated gearbox with a 1.5 service factor. No feed throat, no control panel. Water cooled barrel. Last used as a secondar...
Elk Grove Village, IL
Buy Farrel Co-Rotating Twin Screw Extruder with Gala & Acrison Feeder
- Manufacturer: Acrison
54182001 Used Farrel Twin Screw Pelletizing Line Consisting Of: (1) Farrel 37 mm FTX80 co-rotating twin screw extruder, 5 zone electrically heated, water cooled, approximately 40:1 L/D. Driven by a 25 hp, 500 vol...
Belvidere, IL
Trusted Seller
1994 LEISTRITZ MICRO 18
- Manufacturer: Leistritz
Used 18mm approximately 28/1 L/D Leistritz Micro-18 Co-Rotating Twin Screw Extruder, serial #473614, new 1994. 500 RPM screw speed. 6 Barrel Segments, Top Ports In Segments 1, 2, and 6. 6 Barrel Zones Controlled ...
Hainesport, NJ
DAVIS STANDARD 165mm (6.5″) EXTRUDER 19033
- Manufacturer: Davis-Standard
One used (1) Davis Standard model 165MM60T 165mm (6.49″) extruder having a 34:1 L/D ratio with a nine (9) zone electrically heated, water cooled (closed loop), vented and plugged barrel at presently an 89″ center...
Elk Grove Village, IL
DAVIS STANDARD 75mm 32:1 L/D 18831
- Manufacturer: Davis-Standard
One (1) Used Davis Standard 75mm (2.95″) 32:1 L/D Model DSPW 75IN25 single screw extruder. S/N 72635. SO 80076. Barrel is six (6) zone electrically heated, water cooled(closed loop), and non-vented barrel at a 48...
Elk Grove Village, IL