Used log turner

Sharp Chain Reducer Circular

• Manufacturer: Sharp

- To handle logs up to 15" in diameter x 20' long - Sprocket style log turner c/w centering arms and overhead holddown rolls - 3" wide sharp chain c/w hydraulic drive - Land East reducer module c/w three (3) key ...

MORBARK CIRCULAR CARRIAGE SYSTEM

• Manufacturer: Morbark

- 6" diameter to 36" diameter logs up to 20' long - Log stop and loader - Morbark Low mill style log turner - 36" opening Morbark Carriage - Fabricated steel frame - Three (3) knee assemblies c/w electric linesha...

5' Salem Reducer Twin Sharp Chain System

• Manufacturer: Sharp

- To handle logs up to 24" in diameter x 16' long - Sprocket style log turner c/w overhead holddown rolls - 3" wide Sharp Chain c/w hydraulic drive - USNR reducer module c/w step disc head and linear positioners ...

Chip-N-Saw Canter Quad System

• Manufacturer: CAN CAR

Chip-N-Saw Canter Quad System consisting of:- - Double length infeed equipment was manufactured by Optimil in 1994 - Log turner assembly - Double length half taper infeed. 53' long from turner rolls to bottom he...

Sharp Chain Reducer Twin Bandmill System

• Manufacturer: Sharp

- To handle logs up to 18" in diameter x 20 feet long - VK log singulator - Sprocket style log turner c/w centering arms and overhead holddown rolls - 3" wide Sharp Chain c/w hydraulic drive - USNR reducer module...

60" CAE Carriage

• Manufacturer: CAE

- Manufactured approximately 1988 - 3 Knee c/w Sharpe linear positioners - Vee and flat wheels - Cant flippers - Overall knee width 21" (14" between the knee faces) - Two (2) accumulators - Frame is approximately...

COMACT DDM6 PROFILING CANTERLINE

• Manufacturer: Comact

- Built in 2006 - 4" to 10" diameter logs, 8 feet long @ up to 650FPM - Comact Wave Feeder (9' - 6" between end walls) - V flight Infeed Conveyor c/w eletric drive - V flight scan chain c/w electric drive - Quad ...

10" Chip-N-Saw Mark II

• Manufacturer: Chip-N-Saw

- Build in 1978 - Forano knuckle style log turner - 18' half taper infeed c/w overhead hold down rolls and servo positioned lift - Mark II four sided canter - 2 x 4 spline bottom head - Drum style side heads c/w ...

20" Chip-N-Saw Line

- Infeed chain conveyor - Log turner - Single length infeed for 20' c/w holddown rolls and servo positioner for bed lift - 4 sided canter (bottom head (2 x 4 spline), side heads and top head c/w servo positioners...

COMACT DDM6 FOUR (4) SIDED CANTER SYSTEM

• Manufacturer: Comact

- Built in 1997 - 4" diameter to 12" diameter - 3", 4" and 6" cants - up to 450 FPM - DDM6 - Feedroll log turner - quad roll c/w positioning cylinders - One (1) pair of vertical and one (1) pair of horizontal inf...

CAE Sharp Chain Reducer Quad Bandmill System

• Manufacturer: Sharp

- Knuckle style log turner - Centering infeed conveyor consisting of: - Four (4) pairs of idling centering rolls c/w mechanical centering linkages assembly - One (1) pair of hydraulically driven spiked feedrolls ...

Comact DDM10 Line

• Manufacturer: Comact

- 10 years old - Approx. 120' V-flite conveyor including drive and attached control devices - Flying log turner - new HD upgrade 2011-12? (Quad roll) - DDM10 full profile machine, 480 volt - All drive units, moto...

Comact DDM 12-SBP Profile Curve Sawing Canter Line

• Manufacturer: Comact

- Built in 2001 - 8' to 16' - 4" to 21" butt (maximum 23" envelope) - 400 FPM @ 60 hertz - 575 volt, 3 phase, 60 hertz - 'V' flight scanning conveyor approximately 58' long c/w 20 HP electric drive - Quad roll lo...

Optimil DLI Four (4) Sided Canter/Quad System

• Manufacturer: Optimil

- Located on the North Island of New Zealand - 8' to 20', up to 28" in diameter - Built in 1995 - V-flight auto rotation scanning conveyor - Optimil Feedroll log turner c/w linear positioners for up/down, two (2)...