Used Mills (Mineral Processing)

Unused rubber liners for a 3.4 x 6 m Fuller ball mill

• Manufacturer: Goma

- Unused surplus neoprene rubber liners made by Metso - Designed for 3.4 x 6 m Fuller ball mill - In storage, available now - Stored in shipping container - Available as a full set only

6 x 17 Ft. Marcy Ball Mills

- Used Refurbished Marcy Ball Mills - 2 Available - 17 ft. 19 in Long x 6 ft. 4 in. Width - 450 HP Weg Motor, 480 volt - Soft Start Motor System - David Brown Gearbox G17 9:1 ratio - Voith.562 EPK Clutch ...

8 x 17 Ft. Kennedy Van Saun Ball Mills

• Manufacturer: KVS

-3 Available -Siemens 400 HP 4,000 Volt Motor -With Falk Gear Box 6.95 Ratio -Eaton Air Clutch -Low & High pressure Bearing Lube system -Rubber Liners -Plates and guards -Single Helical Main Gears and Pinion Gear...

8.5 x 13.5 ft Unused Outotec Ball Mills with 450 HP

• Manufacturer: Larox

- Unused Outotec Ball mills - Delivered to site, never installed or operated - 2 units available - 8.6 x 13.5 ft mill shell (3.2 x 5.6 m) - Trunnion supported ball mill - Ring and pinion gear drive - Mill drawing...

DENVER 4' x 5' Ball Mill

• Manufacturer: Denver

HP: KW: DENVER 4' x 5' Ball Mill Diameter: 4'

ALLIS CHALMERS 9' x 12' Regrind Ball Mill with 500 HP Motor

• Manufacturer: Allis-Chalmers

KW: ALLIS CHALMERS 9' x 12' Regrind Ball Mill with 500 HP, 60 Hz Motor

SVEDALA 15' W x 29' L Ball Mill with 3750 HP Motor

• Manufacturer: Svedala

Used SVEDALA 15' W x 29' L (4.6m x 8.8m) Ball Mill with 3750 HP Motor

NORDBERG 15' x 19' (4.6m x 5.8m) Ball Mill

• Manufacturer: Metso

NORDBERG 15' x 19' (4.6m x 5.8m) Ball Mill with 3000 HP Motor 2 pc Shell Westinghouse 3000 HP (2237 kW) Synchronous Motor Spare Pinion

EIMCO 5' x 5' (1.5m x 1.5m) Ball Mill

• Manufacturer: FLSmidth

EIMCO 5' x 5' (1.5m x 1.5m) Ball Mill Babbitt Bearings G.E. 30 HP (22 kW) Motor

DENVER 4' x 8' (1.2m x 2.4m) Skidded Ball Mill with 50 HP motor

• Manufacturer: Metso

DENVER 4' x 8' (1.2m x 2.4m)Skidded Ball Mill with 50 HP motor Previously used in a lime slaking system 50 HP (37 kW) Motor

CANADIAN ALLIS CHALMERS 8' x 10' (2.4m x 3m) Ball Mill with 400 HP Motor

• Manufacturer: Allis-Chalmers

CANADIAN ALLIS CHALMERS 8' x 10' (2.4m x 3m) Ball Mill with 400 HP (298 kW) Motor Herringbone Gears

MARCY 8' x 6' (2.4m x 1.8m) Ball Mill, wet grind, rubber liners, No Motor

• Manufacturer: Metso

MARCY 8' x 6' (2.4m x 1.8m) Ball Mill, wet grind, rubber liners, No Motor Wet Grind Requires 250 HP Motor (Not Included)

Hardinge 10ft Dia. x 5ft Long Conical Ball Mill

• Manufacturer: Hardinge

Trommel Discharge Size: 10ft Dia. x 5ft Long | Drive: No Motor Included | Gearbox: Falk Enclosed Gear Drive | Ratio: 7.211

FLSMIDTH 14'1" dia. x 26'3" L (4.3m W. x 8m L) FT Series (Fulller-Traylor) Ball Mill

• Manufacturer: FLSmidth

KW: FLSMIDTH 14'1" dia. x 26'3" L (4.3m W. x 8m L) FT Series (Fulller-Traylor) Ball Mill, 3000 HP 13.7' EGD x 25'9" EGL Wet Grinding, Overflow Discharge Toshiba 3,000 HP Induction Motor 232-Tooth Single Helical B...

Allis Chalmers 5ft Dia. x 7ft Long Ball Mill

• Manufacturer: Allis-Chalmers

Rebuilt, Unused, and Ready to Ship Mill Feed and Discharge Heads, Bull Gear and Pinion Gear Inspected, and NDT Tested New Steel Shell New Trunnion Bearings, Pedestals and Caps with Integral Oil Sump and Oil Retur...