Used processing

Hosokawa Alpine Fluidised Bed Opposted Jet Mill, Model 630 AFG 1

• Manufacturer: Hosokawa
• Model: AFG

Hosokawa Alpine Fluidised Bed Opposted Jet Mill, Model 630 AFG 1 Used Hosokawa Alpine Fluidised Bed Opposed Jet Mill, Model 630 AFG 1, 630 mm diameter chamber, (4) nozzles, single wheel classifier, mounted on fra...

HOSOKAWA 100 AFG

• Manufacturer: Hosokawa
• Model: AFG

Used Hosokawa multiprocessor ZPS milling machine including an upside down Acm with ATP classifier and Hosokawa / Alpine 100 AFG counter jet mill with 55kW compressor powered by a 1.0 kW motor operating at 22,000 ...

6 x 17 Ft. Marcy Ball Mills

- Used Refurbished Marcy Ball Mills - 2 Available - 17 ft. 19 in Long x 6 ft. 4 in. Width - 450 HP Weg Motor, 480 volt - Soft Start Motor System - David Brown Gearbox G17 9:1 ratio - Voith.562 EPK Clutch ...

8 x 17 Ft. Kennedy Van Saun Ball Mills

• Manufacturer: KVS

-3 Available -Siemens 400 HP 4,000 Volt Motor -With Falk Gear Box 6.95 Ratio -Eaton Air Clutch -Low & High pressure Bearing Lube system -Rubber Liners -Plates and guards -Single Helical Main Gears and Pinion Gear...

1.5 x 3 m (~5 x 10 ft) New ball mill

- New unused ball mill made in North America - 1.5 x 3 meter internal shell dimension, less liners - Single piece rolled steel shell - Tire Driven - Rubber liner package with installation hardware - Rubber lined ...

13 x 18.6 ft Nordberg Rod/ Ball mill with 1,500 HP

• Manufacturer: Symons - Nordberg

- 1500 hp (1125 kw) AC 60 Hz synchronous motor, 225rpm - Eaton Fawick air clutch 46VC 1200 - Mill shell and cast heads - Feed and discharge trunnions and liners - Trunnion bearing assemblies - Refurbished girth g...

18 x 27 ft (5.5 x 8.1 m) Citic Ball Mill with 5,500 HP

Unused 18 x 27 ft (5.5 x 8.1 m) Citic Ball Mill with 5,500 HP (4,100 kW) 893 RPM WRIM induction motor. - Rubber liners, 2 sets - High- and low-speed drive couplings - Sole plates Additional motor info: -WRIM - 89...

9 x 7 ft Allis Chalmers Ball Mill

• Manufacturer: Allis-Chalmers

- 9 ft dia x 7 ft length ball mill - Manufactured by Allis Chalmers - Configured for wet grinding and overflow discharge - Mill components disassembled, inspected, cleaned, refurbished, and painted - mill shell w...

8.5 x 13.5 ft Unused Outotec Ball Mills with 450 HP

• Manufacturer: Larox

- Unused Outotec Ball mills - Delivered to site, never installed or operated - 2 units available - 8.6 x 13.5 ft mill shell (3.2 x 5.6 m) - Trunnion supported ball mill - Ring and pinion gear drive - Mill drawing...

10.5 x 18.5 ft Unused Outotec Ball Mill with 1,000 HP

• Manufacturer: Larox

- Unused surplus Outotec ball mills - 2 matching units available - Delivered to site, never installed or operated - 10.5 x 18.4 ft mill shell (3.2 x 5.6 m) - Cast mill heads - Trunnion supported mill - Ring and p...

9 x 10 ft (2.75 x 3 m) Allis Chalmers ball mill with 400 HP

• Manufacturer: Allis-Chalmers

- 9 x 10 ft Allis Chalmers ball mill - Feed and discharge heads - Configured for overflow discharge and wet grinding - 2 piece bull gear with 248 teeth and 13 inch face - 20 tooth pinion with assembly - 2 lubrica...

8 x 6 ft (2.5 x 1.8 m) Hardinge conical ball mill with 200 HP

• Manufacturer: Hardinge

- 8 x 6 ft Hardinge conical ball mill on a steel skid - Wet grinding, overflow discharge - Single piece shell with access hatch - Falk gear reducer: 5.86:1 reduction ratio, 1.5 SF - Liners installed - Double heli...