Building Filters
- Trusted Seller
ALBA ECAV 16
used
- Manufacturer: Alba
ALBA ECAV 16 Straightener hyperbolic rotor coils made of iron in the straight bars from a hyperbolic rotor from 6 mm to 12 mm. The cutting system to cut iron straightening without interrupting amentando duty cy...
Malaga, Spain - Trusted Seller
ALBA CRM 45
used
- Manufacturer: Alba
ALBA CRM 45 Shears for cutting longitudinal bars up 40mm diameter (400N/mm.2.). Body monoblock casting. Cutting through pedal drive and side lever. Self-lubricated gears. Interchangeable cutting blades (8 edges)....
Malaga, Spain - Trusted Seller
ALBA C42L
used
- Manufacturer: Alba
ALBA C42L Shears for cutting longitudinal bars up 42mm diameter (450N/mm.2.). Body monoblock casting. Cutting through pedal drive and side lever. Self-lubricated gears. Interchangeable cutting blades (8 edges). E...
Malaga, Spain - Trusted Seller
ALBA CRM 35
used
- Manufacturer: Alba
- Model: CRM 35
ALBA CRM 35 Shears for cutting longitudinal bars up 32mm diameter (400N/mm.2.). Body monoblock casting. Cutting through pedal drive and side lever. Self-lubricated gears. Interchangeable cutting blades (8 edges)....
Malaga, Spain - Trusted Seller
ALBA C32L
used
- Manufacturer: Alba
ALBA C32L Shears for cutting longitudinal bars up 28mm diameter (450N/mm.2.). Body monoblock casting. Cutting through pedal drive and side lever. Self-lubricated gears. Interchangeable cutting blades (8 edges).
Malaga, Spain - Trusted Seller
ALBA DAR 36 L
used
- Manufacturer: Alba
ALBA DAR 36 L turntable forward and reverse rotation The table can turn in two directions of operation. angles selector Desired angle is obtained by inserting the pin in the bending table periphery. two drive s...
Malaga, Spain - Trusted Seller
ALBA DAR 55
used
- Manufacturer: Alba
ALBA DAR 55 Maximum bending diameter 45mm at 650N / mm² Two speed New electrical panel Double pedal actuation
Malaga, Spain - Trusted Seller
ALBA DAR 45 P
used
- Manufacturer: Alba
ALBA DAR 45 P Three working systems. Automatical programmation. 300 possible shapes, with 10 angles each, storables. Angles corrector. Counter of bent pieces. Manual selection of angles, by means of pins. Continu...
Malaga, Spain 
ALBA CRM 45 2006
used
- Manufacturer: Alba
ELECTRIC CROPPERS 8 Cutting edges blades Monobloc body in cast steel No oiling point Minimum and cheap maintenance Endurance (30-40 years) Mecanically (CRM) or Hydraulically (CH)operated
Pontevedra, Spain
2007 ALBA DAE 16
used
- Manufacturer: Alba
Stirrup bender ALBA DAE 16 Alba's manual stirrup bending machines are used for the production of stirrups, whose diameters do not usually exceed 12 mm. They are therefore smaller than conventional stirrup bending...
Pontevedra, Spain
2004 ALBA CRM 35
used
- Manufacturer: Alba
- Model: CRM 35
ELECTRIC CROPPERS 8 Cutting edges blades Monobloc body in cast steel No oiling point Minimum and cheap maintenance Endurance (30-40 years) Mechanically (CRM) or Hydraulically (CH)operated
Pontevedra, Spain
ALBA DAR 35 BENDER
used
- Manufacturer: Alba
Great efficiency and quality of work due to: Two bending speeds (the fast one for small diameters). Pre-setting of 3 different angles. Lower-able lateral rollers. Four slid able rulers for better service and accu...
Pontevedra, Spain