- Trusted Seller
RANDCASTLE Ø51 мм × 203 мм
- Manufacturer: RANDCASTLE
Used 2" O.D. x 8" Wide Randcastle Sheet Extrusion 3-Roll Stack including Pull Roll Station and Single Position Winder.
Hainesport, NJ - Trusted Seller
BUSS 200 HP
- Manufacturer: Buss
Used 100mm Buss kneader with 9/1 L/D barrel. Driven by 200 hp DC motor, includes 5.94/1 gearbox, jacketed barrel and clam shell barrel opening. Includes operator control panel. Kneader will discharge into approxi...
Hainesport, NJ - Trusted Seller
2003 WERNER & PFLEIDERER ZSK20
- Manufacturer: WP
- Model: ZSK20
Used 20mm Werner & Pfleiderer model ZSK20 co-rotating twin screw extruder. Has 40/1 L/D barrel at 43" centerline height driven through a 3:1 gearbox with a 37-Newton meter torque capacity per screw shaft. Extrude...
Hainesport, NJ - Trusted Seller
2008 COPERION ZSK-40-MEGA
- Manufacturer: Coperion Waeschle
Used 40mm Coperion Mega 40 co-rotating twin screw extruder. New 2008. No barrels or screws included. Driven by 200 hp AC motor, 1790 rpm, with Powerflight VFD controller. Has 1.155 gear ratio supplying 1200 rpm s...
Hainesport, NJ - Trusted Seller
Conair D400H
- Manufacturer: Conair
- Model: D400H
Used Conair model D400H high heat desiccant dryer, 300 cfm. Have carousel desiccant cartridges, operator controls, no hopper. Previously used with 900-1000 lb hopper.
Hainesport, NJ - Trusted Seller
THORESON MCCOSH TD2000
- Manufacturer: Thoreson McCosh
Used 6,000 lb. Thoreson McCosh Desiccant Dryer Model TD2000. Serial #201-703-05. 480 volt, AC input, 20 hp. Amps 236.0, kw 182.0. No hopper included.
Hainesport, NJ - Trusted Seller
UNA-DYN GS150
- Manufacturer: Una-Dyn
Used Una Dyn Piovan Desiccant Dryer. Model GS150, serial #237240-01-01-0903. Rated at 150 cfm. Includes approximately 800 LB., 30" diameter x 72" straight side x 19" cone bottom insulated hopper with top mounted ...
Hainesport, NJ 
PET Sheet Extrusion Line – 48” Wide, 2,000 lbs/hr, OMV D140 Extruder, (
54129001 Used PET Sheet Extrusion Line 48" Wide, 2,000 lbs/hr, OMV D140 Extruder (Used) 350 HP main motor; 30 HP drive system; Rated up to 2,000 lbs/hour (dependent on material and configuration); Multi-zone coo...
Belvidere, IL- Trusted Seller
BATTENFELD CINCINNATI CM55
- Manufacturer: Battenfeld-Cincinnati
Used Battenfeld-Cincinnati model CM55 counter rotating approximately 55mm diameter twin screw extruder. Conical screw design. Barrel is electrically heated and air cooled in three zones with air blowers with 0.20...
Hainesport, NJ - Trusted Seller
Cincinnati CMT80L-APC
- Manufacturer: Cincinnati
- Model: CMT
Used Cincinnati model CMT80L-APC conical counter rotating twin screw plastic extruder. Screw length approximately 1,665mm long x 80mm diameter at the discharge. Has adaptor plate that reduces the barrel exit down...
Hainesport, NJ - Trusted Seller
Hainesport, NJ - Trusted Seller
Hainesport, NJ - Trusted Seller
Hainesport, NJ - Trusted Seller
BERLYN HV-3
- Manufacturer: BERLYN
Used 18" wide Berlyn high velocity air stripper. Model HV-3, Sserial #1021171. Has 5 HP blower, 460 volt, 3 phase, 60 hertz. Includes starter.
Hainesport, NJ - Trusted Seller
GALA 38" x 39"
- Manufacturer: GALA
Used Gala SS bin only. Square construction, 38" x 39" with hinged top cover on 1/3 of top of bin, and openings on balance of 2/3. No pumps or filters included.
Hainesport, NJ
Tip: Enter manufacturer, model or keyword
